Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userFluctuation characteristics of the TCV snowflake divertor measured with high speed visible imaging
54
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Tangentially viewing fast camera footage of the low-field side snowflake minus divertor in TCV is analysed across a four point scan in which the proximity of the two X-points is varied systematically. The motion of structures observed in the post- processed movie shows two distinct regions of the camera frame exhibiting differing patterns. One type of motion in the outer scrape-off layer remains present throughout the scan whilst the other, apparent in the inner scrape-off layer between the two nulls, becomes increasingly significant as the X-points contract towards one another. The spatial structure of the fluctuations in both regions is shown to conform to the equilibrium magnetic field. When the X-point gap is wide the fluctuations measured in the region between the X-points show a similar structure to the fluctuations observed above the null region, remaining coherent for multiple toroidal turns of the magnetic field and indicating a physical connectivity of the fluctuations between the upstream and downstream regions. When the X-point gap is small the fluctuations in the inner scrape-off layer between the nulls are decorrelated from fluctuations upstream, indicating local production of filamentary structures. The motion of filaments in the inter-null region differs, with filaments showing a dominantly poloidal motion along magnetic flux surfaces when the X-point gap is large, compared to a dominantly radial motion across flux-surfaces when the gap is small. This demonstrates an enhancement to cross-field tranport between the nulls of the TCV low-field-side snowflake minus when the gap between the nulls is small.
rate research
Read More
Using high speed imaging of the divertor volume, the region close to the X-point in MAST is shown to be quiescent. This is confirmed by three different analysis techniques and the quiescent X-point region (QXR) spans from the separatrix to the 1.02 flux surface. Local reductions to the atomic density and effects associated with the camera viewing geometry are ruled out as causes of the QXR, leaving quiescence in the local plasma conditions as being the most likely cause. The QXR is found to be ubiquitous across a significant operational space in MAST including L-mode and H-mode discharges across wide ranges of line averaged density, plasma current and NBI power. When mapped to the divertor target the QXR occupies approximately an e-folding length of the heat-flux profile, containing approximately 60% of the total heat flux to the target, and also shows a tendency towards higher frequency shorter lived fluctuations in the ion-saturation current. This is consistent with short- lived divertor localised filamentary structures observed further down the outer divertor leg in the camera images, and suggests a complex multi-region picture of filamentary transport in the divertor.
The aim of this work is to provide an understanding of detachment at TCV with emphasis on analysis of the Balmer line emission. A new Divertor Spectroscopy System has been developed for this purpose. Further development of Balmer line analysis techniques has allowed detailed information to be extracted from the three-body recombination contribution to the n=7 Balmer line intensity. During density ramps, the plasma at the target detaches as inferred from a drop in ion current to the target. At the same time the Balmer $6rightarrow2$ and $7rightarrow2$ line emission near the target is dominated by recombination. As the core density increases further, the density and recombination rate are rising all along the outer leg to the x-point while remaining highest at the target. Even at the highest core densities accessed (Greenwald fraction 0.7) the peaks in recombination and density may have moved not more than a few cm poloidally away from the target which is different to other, higher density tokamaks, where both the peak in recombination and density continue to move towards the x-point as the core density is increased. The inferred magnitude of recombination is small compared to the target ion current at the time detachment (particle flux drop) starts at the target. However, recombination may be having more localized effects (to a flux tube) which we cannot discern at this time. Later, at the highest densities achieved, the total recombination does reach levels similar to the particle flux.
An analytical model previously developed to study the structure of the magnetic field for the TEXTOR-DED [S.S. Abdullaev et al. Phys. Plasmas, 6, 153 (1999)] is applied to the similar study of the Ergodic Divertor of Tore Supra tokamak [Ph. Ghendrih, Plasma Phys. Control. Fusion, 38, 1653 (1996)]. The coil configuration of ED Tore Supra consists of six modules equidistantly located along the toroidal direction on the low-field-side of the torus with given toroidal and poloidal extensions. The Hamiltonian formulation of field line equations in straight-field-line coordinates (Boozer coordinates) and the computationally efficient mapping method for integration of the Hamiltonian field line equations are used to study the magnetic field structure in the ED. Asymptotical formulas for the perturbation magnetic field created by the ED coils are obtained and the spectrum of magnetic perturbations is analyzed and compared with the one of the TEXTOR-DED. The structure of ergodic and laminar zones are studied by plotting Poincare sections, so-called laminar plots (contour plots of wall to wall connection lengths) and magnetic footprints. The radial profiles of field line diffusion coefficients are calculated for different perturbation currents and it is found that for the Tore Supra case in the ergodic zone the numerical field line diffusion coefficients perfectly follow the quasilinear formula for smaller perturbation currents although the situation is different for the maximum perturbation current.
Global gradient driven GENE gyrokinetic simulations are used to investigate TCV plasmas with negative triangularity. Considering a limited L-mode plasma, corresponding to an experimental triangularity scan, numerical results are able to reproduce the actual transport level over a major fraction of the plasma minor radius for a plasma with $delta_{rm LCFS}=-0.3$ and its equivalent with standard positive triangularity $delta$. For the same heat flux, a larger electron temperature gradient is sustained by $delta<0$, in turn resulting in an improved electron energy confinement. Consistently with the experiments, a reduction of the electron density fluctuations is also seen. Local flux-tube simulations are used to gauge the magnitude of nonlocal effects. Surprisingly, very little differences are found between local and global approaches for $delta>0$, while local results yield a strong overestimation of the heat fluxes when $delta<0$. Despite the high sensitivity of the turbulence level with respect to the input parameters, global effects appear to play a crucial role in the negative triangularity plasma and must be retained to reconcile simulations and experiments. Finally, a general stabilizing effect of negative triangularity, reducing fluxes and fluctuations by a factor dependent on the actual profiles, is recovered.
In future nuclear fusion reactors high heat load events, such as edge-localised modes (ELMs), can potentially damage divertor materials and release impurities into the main plasma, limiting plasma performance. The most difficult to handle are type I ELMs since they carry the largest fraction of energy from the plasma and therefore deposit the largest heat flux at the target and on first wall materials. Knowing the temperature of the ions released from ELM events is important since it determines the potential sputtering they would cause from plasma facing materials. To make measurements of Ti by retarding field energy analyser (RFEA) during type I ELMs a new operational technique has been used to allow faster measurements to be made; this is called the fast swept technique (FST).
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
