Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userStrategy to Nonlinearly Deplete Irreversible Li Consumption in Si-rich Li-Ion Batteries
120
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Despite recent significant developments of Si composites, use of silicon with significance in the anodes for Li-ion batteries is still limited. In fact, nominal energy density is to be saturated around ~750 Wh/L regardless of cell-types under the current material strategies. Use of Si-rich anode can push the limit; however, the prolonged irreversible Li consumption becomes more prominent. We previously showed that repeating c-Li3.75(+{delta})Si formation/decomposition, typically recognized to degrade the anodes, can improve the irreversibility and accumulatively minimize the gross consumption. Utilizing the insights combined with prelithiation techniques, here we provide prototypic cell designs that can nonlinearly deplete the consumption.
rate research
Read More
Using a new class of (BH4)- substituted argyrodite Li6PS5Z0.83(BH4)0.17, (Z = Cl, I) solid electrolyte, Li-metal solid-state batteries operating at room temperature have been developed. The cells were made by combining the modified argyrodite with an In-Li anode and two types of cathode: an oxide, LixMO2 (M = 1/3Ni, 1/3Mn, 1/3Co; so called NMC) and a titanium disulfide, TiS2. The performance of the cells was evaluated through galvanostatic cycling and Alternating Current AC electrochemical impedance measurements. Reversible capacities were observed for both cathodes for at least tens of cycles. However, the high-voltage oxide cathode cell shows lower reversible capacity and larger fading upon cycling than the sulfide one. The AC impedance measurements revealed an increasing interfacial resistance at the cathode side for the oxide cathode inducing the capacity fading. This resistance was attributed to the intrinsic poor conductivity of NMC and interfacial reactions between the oxide material and the argyrodite electrolyte. On the contrary, the low interfacial resistance of the TiS2 cell during cycling evidences a better chemical compatibility between this active material and substituted argyrodites, allowing full cycling of the cathode material, 240 mAhg-1, for at least 35 cycles with a coulombic efficiency above 97%.
Controlling nanostructure from molecular, crystal lattice to the electrode level remains as arts in practice, where nucleation and growth of the crystals still require more fundamental understanding and precise control to shape the microstructure of metal deposits and their properties. This is vital to achieve dendrite-free Li metal anodes with high electrochemical reversibility for practical high-energy rechargeable Li batteries. Here, cryogenic-transmission electron microscopy was used to capture the dynamic growth and atomic structure of Li metal deposits at the early nucleation stage, in which a phase transition from amorphous, disordered states to a crystalline, ordered one was revealed as a function of current density and deposition time. The real-time atomic interaction over wide spatial and temporal scales was depicted by the reactive-molecular dynamics simulations. The results show that the condensation accompanied with the amorphous-to-crystalline phase transition requires sufficient exergy, mobility and time to carry out, contrary to what the classical nucleation theory predicts. These variabilities give rise to different kinetic pathways and temporal evolutions, resulting in various degrees of order and disorder nanostructure in nano-sized domains that dominate in the morphological evolution and reversibility of Li metal electrode. Compared to crystalline Li, amorphous/glassy Li outperforms in cycle life in high-energy rechargeable batteries and is the desired structure to achieve high kinetic stability for long cycle life.
The capacity and stability of constituent electrodes determine the performance of Li-ion batteries. In this study, density functional theory is employed to explore the potential application of recently synthesized two dimensional phosphorene as electrode materials. Our results show that Li atoms can bind strongly with phosphorene monolayer and double layer with significant electron transfer. Besides, the structure of phosphorene is not much influenced by lithiation and the volume change is only 0.2%. A semiconducting to metallic transition is observed after lithiation. The diffusion barrier is calculated to 0.76 and 0.72 eV on monolayer and double layer phosphorene. The theoretical specific capacity of phosphorene monolayer is 432.79 mAh/g, which is larger than other commercial anodes materials. Our findings show that the high capacity, low open circuit voltage, small volume change and electrical conductivity of phosphorene make it a good candidate as electrode material.
Li-ion batteries gradually lose their capacity with time and use; therefore, ageing forecasts are key to designs of battery powered systems. So far, cell-type-specific studies without standardised testing practices have lead to a variety of ageing models in which generality, simplicity, and accuracy seem exclusive. Previous studies hint to an interplay of multiple mechanisms leading to capacity loss, which depend on cell chemistry and are affected by temperature, state of charge, and cycling rate. Here we show that, despite this complexity, the time dependence of the actual capacity follows a unique master curve, for several cell types aged under various different conditions. We discuss the statistical origin of this common behaviour, and the testing practice required for the characterisation of a model. The master curve is a stretched exponential that describes many other phenomena in nature and is theoretically justified within a diffusion-to-traps depletion model. These findings provide a simple and broadly applicable framework for accurate life-time predictions.
For a successful integration of silicon in high-capacity anodes of Li-ion batteries, its intrinsic capacity decay on cycling due to severe volume swelling should be minimized. In this work, Ni-Sn intermetallics are studied as buffering matrix during reversible lithiation of Si-based anodes. Si/Ni-Sn composites have been synthetized by mechanical milling using C and Al as process control agents. Ni3Sn4, Ni3Sn2 intermetallics and their bi-phasic mixture were used as constituents of the buffering matrix. The structure, composition and morphology of the composites have been analyzed by X-ray diffraction (XRD), 119Sn Transmission Mossbauer Spectroscopy (TMS) and scanning electron microscopy (SEM). They consist of ~ 150 nm Si nanoparticles embedded in a multi-phase matrix, the nanostructuration of which improves on increasing the Ni3Sn4 amount. The electrochemical properties of the composites were analyzed by galvanostatic cycling in half-cells. Best results for practical applications are found for the bi-phasic matrix Ni3Sn4-Ni3Sn2 in which Ni3Sn4 is electrochemically active while Ni3Sn2 is inactive. Low capacity loss, 0.04 %/cycle, and high coulombic efficiency, 99.6%, were obtained over 200 cycles while maintaining a high reversible capacity above 500 mAh/g at moderate regime C/5
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
