Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userAdaptive inversion algorithm for 1.5 um visibility lidar incorporating in situ Angstrom wavelength exponent
287
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
As one of the most popular applications of lidar systems, the atmospheric visibility is defined to be inversely proportional to the atmospheric extinction coefficient at 0.55 um. Since the laser at 1.5 um shows the highest maximum permissible exposure in the wavelength ranging from 0.3 um to 10 um, the eye-safe 1.5 um lidar can be deployed in urban areas. In such a case, the measured extinction coefficient at 1.5 um should be converted to that at 0.55 um for visibility retrieval. Although several models have been established since 1962, the accurate wavelength conversion remains a challenge. An adaptive inversion algorithm for 1.5 um visibility lidar is proposed and demonstrated by using the in situ Angstrom wavelength exponent, which is derived from either a sun photometer or an aerosol spectrometer. The impact of the particle size distribution of atmospheric aerosols and the Rayleigh backscattering of atmospheric molecules are taken into account. In comparison, the Angstrom wavelength exponent derived from the sun photometer is 7.7% higher than that derived from the aerosol spectrometer. Then, using 1.5 um visibility lidar, the visibility with a temporal resolution of 5 min is detected over 48 hours in Hefei (31.83 N, 117.25 E). The average visibility error between the new method and a visibility sensor (Vaisala, PWD52) is 5.2% with the R-square value of 0.96, while the relative error between another reference visibility lidar at 532 nm and the visibility sensor is 6.7% with the R-square value of 0.91. All results agree with each other well, demonstrating the accuracy and stability of the algorithm.
rate research
Read More
Aqua MODIS, unlike its predecessor on board the Terra spacecraft, had always been thought to have been spared from significant deleterious impacts of electronic crosstalk on its imagery. However, recent efforts brought to our attention the presence of striping artifacts in Aqua MODIS images from band 24 (4.47$mu$m), which upon further inspection proved to have a noticeable impact on the quality of the L1B product and to have been present since the beginning of the mission, in 2002. Using images of the Moon from scheduled lunar observations, we linked the artifacts with electronic crosstalk contamination of the response of detector 1 of band 24 by signal sent from the detector 10 of band 26 (1.375$mu$m), a neighboring band in the same focal plane assembly. In this paper, we report on these findings, the artifact mitigation strategy adopted by us, and on our success in restoring band 24 detector 1 behavior and image quality.
The IceCube neutrino observatory uses $1,mathrm{km}^{3}$ of the natural Antarctic ice near the geographic South Pole as optical detection medium. When charged particles, such as particles produced in neutrino interactions, pass through the ice with relativistic speed, Cherenkov light is emitted. This is detected by IceCubes optical modules and from all these signals a particle signature is reconstructed. A new kind of signature can be detected using light emission from luminescence. This detection channel enables searches for exotic particles (states) which do not emit Cherenkov light and currently cannot be probed by neutrino detectors. Luminescence light is induced by highly ionizing particles passing through matter due to excitation of surrounding atoms. This process is highly dependent on the ice structure, impurities, pressure and temperature which demands an in-situ measurement of the detector medium. For the measurements at IceCube, a $1.7,mathrm{km}$ deep hole was used which {vertically} overlaps with the glacial ice layers found in the IceCube volume over a range of $350,mathrm{m}$. The experiment as well as the measurement results are presented. The impact {of the results, which enable new kind of} searches for new physics with neutrino telescopes, are discussed.
Advances in atomic resolution in situ environmental transmission electron microscopy for direct probing of gas-solid reactions, including at very high temperatures are described. In addition, recent developments of dynamic real time in situ studies at the Angstrom level using a hot stage in an aberration corrected environment are presented. In situ data from Pt and Pd nanoparticles on carbon with the corresponding FFT (optical diffractogram) illustrate an achieved resolution of 0.11 nm at 500 C and higher in a double aberration corrected TEM and STEM instrument employing a wider gap objective pole piece. The new results open up opportunities for dynamic studies of materials in an aberration corrected environment.
We propose a concise approximate description, and a method for efficiently obtaining this description, via adaptive random sampling of the performance (running time, memory consumption, or any other profileable numerical quantity) of a given algorithm on some low-dimensional rectangular grid of inputs. The formal correctness is proven under reasonable assumptions on the algorithm under consideration; and the approachs practical benefit is demonstrated by predicting for which observer positions and viewing directions an occlusion culling algorithm yields a net performance benefit or loss compared to a simple brute force renderer.
The advent of a new generation of large-scale galaxy surveys is pushing cosmological numerical simulations in an uncharted territory. The simultaneous requirements of high resolution and very large volume pose serious technical challenges, due to their computational and data storage demand. In this paper, we present a novel approach dubbed Dynamic Zoom Simulations -- or DZS -- developed to tackle these issues. Our method is tailored to the production of lightcone outputs from N-body numerical simulations, which allow for a more efficient storage and post-processing compared to standard comoving snapshots, and more directly mimic the format of survey data. In DZS, the resolution of the simulation is dynamically decreased outside the lightcone surface, reducing the computational work load, while simultaneously preserving the accuracy inside the lightcone and the large-scale gravitational field. We show that our approach can achieve virtually identical results to traditional simulations at half of the computational cost for our largest box. We also forecast this speedup to increase up to a factor of 5 for larger and/or higher-resolution simulations. We assess the accuracy of the numerical integration by comparing pairs of identical simulations run with and without DZS. Deviations in the lightcone halo mass function, in the sky-projected lightcone, and in the 3D matter lightcone always remain below 0.1%. In summary, our results indicate that the DZS technique may provide a highly-valuable tool to address the technical challenges that will characterise the next generation of large-scale cosmological simulations.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
