Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMicro-optical Tandem Luminescent Solar Concentrators
359
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Traditional concentrating photovoltaic (CPV) systems utilize multijunction cells to minimize thermalization losses, but cannot efficiently capture diffuse sunlight, which contributes to a high levelized cost of energy (LCOE) and limits their use to geographical regions with high direct sunlight insolation. Luminescent solar concentrators (LSCs) harness light generated by luminophores embedded in a light-trapping waveguide to concentrate light onto smaller cells. LSCs can absorb both direct and diffuse sunlight, and thus can operate as flat plate receivers at a fixed tilt and with a conventional module form factor. However, current LSCs experience significant power loss through parasitic luminophore absorption and incomplete light trapping by the optical waveguide. Here we introduce a tandem LSC device architecture that overcomes both of these limitations, consisting of a PLMA polymer layer with embedded CdSe/CdS quantum dot (QD) luminophores and InGaP micro-cells, which serve as a high bandgap absorber on top of a conventional Si photovoltaic. We experimentally synthesize CdSe/CdS QDs with exceptionally high quantum-yield (99%) and ultra-narrowband emission optimally matched to fabricated III-V InGaP micro-cells. Using a Monte Carlo ray-tracing model, we show the radiative limit power conversion efficiency for a module with these components to be 30.8% diffuse sunlight conditions. These results indicate that a tandem LSC-on-Si architecture could significantly improve upon the efficiency of a conventional Si photovoltaic module with simple and straightforward alterations of the module lamination steps of a Si photovoltaic manufacturing process, with promise for widespread module deployment across diverse geographical regions and energy markets.
rate research
Read More
Perovskite-silicon tandem solar cells are currently one of the most investigated concepts to overcome the theoretical limit for the power conversion efficiency of silicon solar cells. For monolithic tandem solar cells the available light must be distributed equally between the two subcells, which is known as current matching. For a planar device design, a global optimization of the layer thicknesses in the perovskite top cell allows current matching to be reached and reflective losses of the solar cell to be minimized at the same time. However, even after this optimization reflection and parasitic absorption losses occur, which add up to 7 mA/cm$^2$. In this contribution we use numerical simulations to study, how well hexagonal sinusoidal nanotextures in the perovskite top-cell can reduce the reflective losses of the combined tandem device. We investigate three configurations. The current density utilization can be increased from 91% for the optimized planar reference to 98% for the best nanotextured device (period 500 nm and peak-to-valley height 500 nm), where 100% refers to the Tiedje-Yablonovitch limit. In a first attempt to experimentally realize such nanophotonically structured perovskite solar cells for monolithic tandems, we investigate the morphology of perovskite layers, which are deposited onto sinusoidally structured substrates.
A simple procedure is demonstrated for fabrication of waveplates which can be released from substrate by laser cutting. Oblique angle deposition, chemical etching and laser inscription steps were used for the final lift-off and release of micro-waveplates in HCl solution.
We demonstrate a photonic radio frequency (RF) transversal filter based on an integrated optical micro-comb source featuring a record low free spectral range of 49 GHz yielding 80 micro-comb lines across the C-band. This record-high number of taps, or wavelengths for the transversal filter results in significantly increased performance including a QRF factor more than four times higher than previous results. Further, by employing both positive and negative taps, an improved out-of-band rejection of up to 48.9 dB is demonstrated using Gaussian apodization, together with a tunable centre frequency covering the RF spectra range, with a widely tunable 3-dB bandwidth and versatile dynamically adjustable filter shapes. Our experimental results match well with theory, showing that our transversal filter is a competitive solution to implement advanced adaptive RF filters with broad operational bandwidths, high frequency selectivity, high reconfigurability, and potentially reduced cost and footprint. This approach is promising for applications in modern radar and communications systems.
We demonstrate significantly improved performance of a microwave true time delay line (TTDL) based on an integrated micro-ring resonator (MRR) Kerr optical comb source with a channel spacing of 49GHz, corresponding to 81 channels over the C-band. The broadband microcomb, with a record low free spectral range of 49GHz, results in a large number of comb lines for the TTDL, greatly reducing the size, cost, and complexity of the system. The large channel count results in a high angular resolution and wide beam steering tunable range of the phased array antenna (PAA). The enhancement of PAA performance matches well with theory, corroborating the feasibility of our approach as a competitive solution towards implementing compact low-cost TTDL in radar and communications systems.
Here we use time-resolved and steady-state optical spectroscopy on state-of-the-art low- and high-bandgap perovskite films for tandems to quantify intrinsic recombination rates and absorption coefficients. We apply these data to calculate the limiting efficiency of perovskite-silicon and all-perovskite two-terminal tandems employing currently available bandgap materials as 42.0 % and 40.8 % respectively. By including luminescence coupling between sub-cells, i.e. the re-emission of photons from the high-bandgap sub-cell and their absorption in the low-bandgap sub-cell, we reveal the stringent need for current matching is relaxed when the high-bandgap sub-cell is a luminescent perovskite compared to calculations that do not consider luminescence coupling. We show luminescence coupling becomes important in all-perovskite tandems when charge carrier trapping rates are < 10$^{6}$ s$^{-1}$ (corresponding to carrier lifetimes longer than 1 ${mu}$s at low excitation densities) in the high-bandgap sub-cell, which is lowered to 10$^{5}$ s$^{-1}$ in the better-bandgap-matched perovskite-silicon cells. We demonstrate luminescence coupling endows greater flexibility in both sub-cell thicknesses, increased tolerance to different spectral conditions and a reduction in the total thickness of light absorbing layers. To maximally exploit luminescence coupling we reveal a key design rule for luminescent perovskite-based tandems: the high-bandgap sub-cell should always have the higher short-circuit current. Importantly, this can be achieved by reducing the bandgap or increasing the thickness in the high-bandgap sub-cell with minimal reduction in efficiency, thus allowing for wider, unstable bandgap compositions (>1.7 eV) to be avoided. Finally, we experimentally visualise luminescence coupling in an all-perovskite tandem device stack through cross-section luminescence images.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
