Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMechanism for femtosecond laser-induced periodic subwavelength structures on solid surface: surface two-plasmon resonance
79
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We present that surface two-plasmon resonance (STPR) in electron plasma sheet produced by femtosecond laser irradiating metal surface is the self-formation mechanism of periodic subwavelength ripple structures. Peaks of overdense electrons formed by resonant two-plasmon wave pull bound ions out of the metal surface and thus the wave pattern of STPR is carved on the surface by Coulomb ablation (removal) resulting from the strong electrostatic field induced by charge separation. To confirm the STPR model, we have performed analogical carving experiments by two laser beams with perpendicular polarizations. The results explicitly show that two wave patterns of STPR are independently carved on the exposure area of target surface. The time-scale of ablation dynamics and the electron temperature in ultrafast interaction are also verified by time-resolved spectroscopy experiment and numerical simulation, respectively. The present model can self-consistently explain the formation of subwavelength ripple structures even with spatial periods shorter than half of the laser wavelength, shedding light on the understanding of ultrafast laser-solid interaction.
rate research
Read More
In this paper the formation mechanisms of the femtosecond laser-induced periodic surface structures (LIPSS) are discussed. One of the most frequently-used theories explains the structures by interference between the incident laser beam and surface plasmon-polariton waves. The latter is most commonly attributed to the coupling of the incident laser light to the surface roughness. We demonstrate that this excitation mechanism of surface plasmons contradicts to the results of laser-ablation experiments. As an alternative approach to the excitation of LIPSS we analyse development of hydrodynamic instabilities in the melt layer.
We study the spectra and damping of surface plasmon-polaritons in double graphene layer structures. It is shown that application of bias voltage between layers shifts the edge of plasmon absorption associated with the interband transitions. This effect could be used in efficient plasmonic modulators. We reveal the influence of spatial dispersion of conductivity on plasmonic spectra and show that it results in the shift of cutoff frequency to the higher values.
Tunability of the surface plasmon resonance wavelength is demonstrated by varying the thickness of Al2O3 spacer layer inserted between the graphene and nanoparticles. By varying the spacer layer thickness from 0.3 to 1.8 nm, the resonance wavelength is shifted from 583 to 566 nm. The shift is due to a change in the electromagnetic field coupling strength between the localized surface plasmons excited in the gold nanoparticles and a single layer graphene film. In contrast, when the graphene film is absent from the system, no noticeable shift in the resonance wavelength is observed upon varying the spacer thickness.
Surface plasmon-polaritons have recently attracted renewed interest in the scientific community for their potential in sub-wavelength optics, light generation and non-destructive sensing. Given that they cannot be directly excited by freely propagating light due to their intrinsical binding to the metal surface, the light-plasmon coupling efficiency becomes of crucial importance for the success of any plasmonic device. Here we present a comprehensive study on the modulation (enhancement or suppression) of such coupling efficiency by means of one-dimensional surface corrugation. Our approach is based on simple wave interference and enables us to make quantitative predictions which have been experimentally confirmed at both the near infra-red and telecom ranges.
One-dimensional (1D) subwavelength corrugated metal structures has been described to support spoof surface plasmon polaritons (SPPs). Here we demonstrate that a modulated 1D subwavelength corrugated metal structure can convert spoof SPPs to propagating waves. The structure is fed at the center through a slit with a connected waveguide on the input side. The subwavelength corrugated metal structure on the output surface is regarded as metasurface and modulated periodically to realize the leaky-wave radiation at the broadside. The surface impedance of the corrugated metal structure is modulated by using cosine function and triangle-wave function, respectively, to reach the radiation effect. Full wave simulations and measuremental results are presented to validate the proposed design.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
