Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userCurrent-modulation annealing to control microwave permittivity in composites with melt-extracted microwires
62
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We investigate the microwave properties of epoxy-based composite containing melt-extracted CoFeBSiNb microwires fabricated by a combined current-modulation annealing (CCMA) technique. We observe a shift of the resonance peak in the effective permittivity spectra of the composite sample containing annealed 25 mm Nb-doped microwires as an applied magnetic field is increased. This observation is consistent with the absorption-dominated impedance for thick microwires and the ferromagnetic resonance phenomenon. It is shown that CCMA is an appropriate technique to release internal residual stresses. Hence, for samples containing small amounts of Nb, we observe that CCMA allows us to suppress the high frequency resonance peak observed in samples containing as-cast wires. However, for samples containing a high amount of Nb, the high frequency peak remains despite the CCMA treatment. In this case, the observation of a two-peak feature in the permittivity spectra is attributed to the coexistence of the amorphous phase and a small amount of nanocrystallites distributed at the wire surface. However, due to large magnetostatic energy of long (35 mm) and short (15 mm) as-cast wires and imperfect wire-epoxy bonding no shift of the resonance peak and the characteristic double peak of the permittivity spectrum can be detected. Overall, CCMA emerges as a promising strategy to control microwave permittivity in composites with melt-extracted microwires.
rate research
Read More
We have investigated the microwave properties of epoxy-based composites containing melt-extracted Co69.25Fe4. 25B13.5-xSi13Nbx (x=0, 1, 3) microwires of various length annealed using a so-called combined current-modulation annealing (CCMA) technique. The observation of a double-peak feature in the permittivity spectra is believed due to the coexistence of the amorphous phase and a small amount of nanocrystallites on the wires with a high Nb content. CCMA was found to be favorable for a better-defined circular anisotropy of microwires and had suppressed the highfrequency peak due to residual stress relief for the composite with 25 mm long wires. Neither the shift of resonance peak nor the characteristic double peak feature was detected for composites containing as-cast 15 or 35 mm long microwires.
Radio, millimetre and sub-millimetre astronomy experiments as well as remote sensing applications often require castable absorbers with well known electromagnetic properties to design and realize calibration targets. In this context, we fabricated and characterized two samples using different ratios of two easily commercially available materials: epoxy (Stycast 2850FT) and magnetite ($mathrm{Fe_{3}O_{4}}$) powder. We performed transmission and reflection measurements from 7 GHz up to 170 GHz with a VNA equipped with a series of standard horn antennas. Using an empirical model we analysed the data to extract complex permittivity and permeability from transmission data; then we used reflection data to validate the results. In this paper we present the sample fabrication procedure, analysis method, parameter extraction pipeline, and results for two samples with different epoxy-powder mass ratios.
The optimization of high frequency giant magnetoimpedance (GMI) effect and its magnetic field sensitivity in melt-extracted Co69.25Fe4.25Si13B12.5Nb1 amorphous microwires, through a multi-step Joule annealing (MSA) technique, was systematically studied. The surface morphology, microstructure, surface magnetic property, and high frequency GMI response of the Co-rich microwires were explored using scanning electron microscopy (SEM), magneto-optical Kerr effect (MOKE) magnetometry, transmission electron microscopy (TEM), and impedance analyzer, respectively. An initial dc current (idc) of 20 mA, which was then increased by 20 mA at every time-step (10 min) up to 300 mA, was applied to the microwires. The MSA of 20 mA to 100 mA remarkably improved the GMI ratio and its field sensitivity up to 760% (1.75 time of that of the as-prepared), and 925%/Oe (more than 17.92 times of that of the as-prepared) at an operating frequency of 20 MHz, respectively. Our study indicates that the MSA technique can enhance the microstructures and the surface magnetic domain structures of the Co-rich magnetic microwires, giving rise to the GMI enhancement. This technique is suitable for improving the GMI sensitivity at small magnetic fields, which is highly promising for biomedical sensing and healthcare monitoring.
A remarkably strong dependence of magnetoimpedance (MI) on tensile stress has been observed in the microwave frequency range for thin CoMnSiB glass-coated microwires exposed to a special thermal treatment. The MI ratio runs into more than 100% at 0.5-1.5 GHz when the tensile stress of 600 MPa is applied to the wire. It was demonstrated that a large MI change at such high frequencies is related predominantly with the dc magnetization orientation. A host of such microwires incorporated into a dielectric matrix may constitute a new sensing medium that is characterized by the stress-dependent effective permittivity. Such medium can be used for the microwave visualization of the stress distribution inside of a composite structure or on its surface.
We study the behavior of wave propagation in materials for which not all of the principle elements of the permeability and permittivity tensors have the same sign. We find that a wide variety of effects can be realized in such media, including negative refraction, near-field focusing and high impedance surface reflection. In particular a bi-layer of these materials can transfer a field distribution from one side to the other, including near-fields, without requiring internal exponentially growing waves.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
