Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userCoherent Feedback Improved Qubit Initialization in the Dispersive Regime
86
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Readout of the state of a superconducting qubit by homodyne detection of the output signal from a dispersively coupled microwave resonator is a common technique in circuit quantum electrodynamics, and is often claimed to be quantum non-demolition (QND) up to the same order of approximation as in the dispersive approximation. However, in this work we show that only in the limit of infinite measurement time is this protocol QND, as the formation of a dressed coherent state in the qubit-cavity system applies an effective rotation to the qubit state. We show how this rotation can be corrected by a coherent operation, leading to improved qubit initialization by measurement and coherent feedback.
rate research
Read More
We study bifurcation measurement of a multi-level superconducting qubit using a nonlinear resonator biased in the straddling regime, where the resonator frequency sits between two qubit transition frequencies. We find that high-fidelity bifurcation measurements are possible because of the enhanced qubit-state-dependent pull of the resonator frequency, the behavior of qubit-induced nonlinearities and the reduced Purcell decay rate of the qubit that can be realized in this regime. Numerical simulations find up to a threefold improvement in qubit readout fidelity when operating in, rather than outside of, the straddling regime. High-fidelity measurements can be obtained at much smaller qubit-resonator couplings than current typical experimental realizations, reducing spectral crowding and potentially simplifying the implementation of multi-qubit devices.
Superconducting electrical circuits can be used to study the physics of cavity quantum electrodynamics (QED) in new regimes, therefore realizing circuit QED. For quantum information processing and quantum optics, an interesting regime of circuit QED is the dispersive regime, where the detuning between the qubit transition frequency and the resonator frequency is much larger than the interaction strength. In this paper, we investigate how non-linear corrections to the dispersive regime affect the measurement process. We find that in the presence of pure qubit dephasing, photon population of the resonator used for the measurement of the qubit act as an effective heat bath, inducing incoherent relaxation and excitation of the qubit. Measurement thus induces both dephasing and mixing of the qubit, something that can reduce the quantum non-demolition aspect of the readout. Using quantum trajectory theory, we show that this heat bath can induce quantum jumps in the qubit state and reduce the achievable signal-to-noise ratio of a homodyne measurement of the voltage.
We compare the performance of continuous coherent feedback, implemented using an ideal single-qubit controller, to that of continuous measurement-based feedback for the task of controlling the state of a single qubit. Here the basic dynamical resource is the ability to couple the system to a traveling-wave field (for example, a transmission line) via a system observable, and the fundamental limitation is the maximum rate that is available for this coupling. We focus on the question of the best achievable control given ideal controllers. To obtain a fair comparison we acknowledge that the amplification involved in measurement-based control allows the controller to use macroscopic fields to apply feedback forces to the system, so it is natural to allow these feedback forces to be much larger than the mesoscopic coupling to the transmission line that mediates both the measurement for measurement-based control and the coupling to the mesoscopic controller for coherent control. Interestingly our numerical results indicate that under the above platform for comparison, coherent feedback is able to exactly match the performance of measurement-based feedback given ideal controllers. We also discuss various properties of, and control mechanisms for, coherent feedback networks.
We proposed a method to engineer the light matter interaction while initializing a qubit in presence of physical constraints utilizing the inverse engineering. Combining the multiple degrees of freedom in the pulse parameters with the perturbation theory, we developed pulses to initialize the qubit within a tightly packed frequency interval to an arbitrary superposition state with high fidelity. Importantly, the initialization induces low off-resonant excitations to the neighboring qubits, and it is robust against the spatial inhomogeneity in the laser intensity. We applied the method to the ensemble rare-earth ions system, and simulations show that the initialization is more robust against the variations in laser intensity than the previous pulses, and reduces the time that ions spend in the intermediate excited state by a factor of 17. The method is applicable to any systems addressed in frequency such as NV centers, superconducting qubits, quantum dots, and molecular qubit systems.
High-fidelity qubit measurements play a crucial role in quantum computation, communication, and metrology. In recent experiments, it has been shown that readout fidelity may be improved by performing repeated quantum non-demolition (QND) readouts of a qubits state through an ancilla. For a qubit encoded in a two-level system, the fidelity of such schemes is limited by the fact that a single error can destroy the information in the qubit. On the other hand, if a bosonic system is used, this fundamental limit could be overcome by utilizing higher levels such that a single error still leaves states distinguishable. In this work, we present a robust readout scheme, applicable to bosonic systems dispersively coupled to an ancilla, which leverages both repeated QND readouts and higher-level encodings to asymptotically suppress the effects of qubit/cavity relaxation and individual measurement infidelity. We calculate the measurement fidelity in terms of general experimental parameters, provide an information-theoretic description of the scheme, and describe its application to several encodings, including cat and binomial codes.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
