Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userContact Angle Hysteresis on Superhydrophobic Stripes
158
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We study experimentally and discuss quantitatively the contact angle hysteresis on striped superhydrophobic surfaces as a function of a solid fraction, $phi_S$. It is shown that the receding regime is determined by a longitudinal sliding motion the deformed contact line. Despite an anisotropy of the texture the receding contact angle remains isotropic, i.e. is practically the same in the longitudinal and transverse directions. The cosine of the receding angle grows nonlinearly with $phi_S$, in contrast to predictions of the Cassie equation. To interpret this we develop a simple theoretical model, which shows that the value of the receding angle depends both on weak defects at smooth solid areas and on the elastic energy of strong defects at the borders of stripes, which scales as $phi_S^2 ln phi_S$. The advancing contact angle was found to be anisotropic, except as in a dilute regime, and its value is determined by the rolling motion of the drop. The cosine of the longitudinal advancing angle depends linearly on $phi_S$, but a satisfactory fit to the data can only be provided if we generalize the Cassie equation to account for weak defects. The cosine of the transverse advancing angle is much smaller and is maximized at $phi_Ssimeq 0.5$. An explanation of its value can be obtained if we invoke an additional energy due to strong defects in this direction, which is shown to be proportional to $phi_S^2$. Finally, the contact angle hysteresis is found to be quite large and generally anisotropic, but it becomes isotropic when $phi_Sleq 0.2$.
rate research
Read More
We discuss an evaporation-induced wetting transition on superhydrophobic stripes, and show that depending on the elastic energy of the deformed contact line, which determines the value of an instantaneous effective contact angle, two different scenarios occur. For relatively dilute stripes the receding angle is above 90$^circ$, and the sudden impalement transition happens due to an increase of a curvature of an evaporating drop. For dense stripes the slow impregnation transition commences when the effective angle reaches 90$^circ$ and represents the impregnation of the grooves from the triple contact line towards the drop center.
A dynamic wetting problem is studied for a moving thin fiber inserted in fluid and with a chemically inhomogeneous surface. A reduced model is derived for contact angle hysteresis by using the Onsager principle as an approximation tool. The model is simple and captures the essential dynamics of the contact angle. From this model we derive an upper bound of the advancing contact angle and a lower bound of the receding angle, which are verified by numerical simulations. The results are consistent with the quasi-static results. The model can also be used to understand the asymmetric dependence of the advancing and receding contact angles on the fiber velocity, which is observed recently in physical experiments reported in Guan et al Phys. Rev. Lett. 2016.
We investigate the transition between the Cassie-Baxter and Wenzel states of a slowly evaporating, micron-scale drop on a superhydrophobic surface. In two dimensions analytical results show that there are two collapse mechanisms. For long posts the drop collapses when it is able to overcome the free energy barrier presented by the hydrophobic posts. For short posts, as the drop loses volume, its curvature increases allowing it to touch the surface below the posts. We emphasise the importance of the contact line retreating across the surface as the drop becomes smaller: this often preempts the collapse. In a quasi-three dimensional simulation we find similar behaviour, with the additional feature that the drop can de-pin from all but the peripheral posts, so that its base resembles an inverted bowl.
Contrasting with its sluggish behavior on standard solids, water is extremely mobile on superhydrophobic materials, as shown for instance by the continuous acceleration of drops on tilted water-repellent leaves. For much longer substrates, however, drops reach a terminal velocity that results from a balance between weight and friction, allowing us to question the nature of this friction. We report that the relationship between force and terminal velocity is non-linear. This is interpreted by showing that classical sources of friction are minimized, so that the aerodynamical resistance to motion becomes dominant, which eventually explains the matchless mobility of water. Our results are finally extended to viscous liquids, also known to be unusually quick on these materials.
When a drop of water is placed on a rough surface, there are two possible extreme regimes of wetting: the one called Cassie-Baxter (CB) with air pockets trapped underneath the droplet and the one characterized by the homogeneous wetting of the surface, called the Wenzel (W) state. A way to investigate the transition between these two states is by means of evaporation experiments, in which the droplet starts in a CB state and, as its volume decreases, penetrates the surfaces grooves, reaching a W state. Here we present a theoretical model based on the global interfacial energies for CB and W states that allows us to predict the thermodynamic wetting state of the droplet for a given volume and surface texture. We first analyze the influence of the surface geometric parameters on the droplets final wetting state with constant volume, and show that it depends strongly on the surface texture. We then vary the volume of the droplet keeping fixed the geometric surface parameters to mimic evaporation and show that the drop experiences a transition from the CB to the W state when its volume reduces, as observed in experiments. To investigate the dependency of the wetting state on the initial state of the droplet, we implement a cellular Potts model in three dimensions. Simulations show a very good agreement with theory when the initial state is W, but it disagrees when the droplet is initialized in a CB state, in accordance with previous observations which show that the CB state is metastable in many cases. Both simulations and theoretical model can be modified to study other types of surface.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
