Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userThe effect of Ag addition on the superconducting properties of the FeSe system
209
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The tetragonal FeSe phase is an intensively investigated iron based superconductor. In this study we examined the influence of Ag addition on the superconducting properties of selenium deficient polycrystalline FeSe0.94. The samples were obtained by solid state reaction and melting methods. XRD analysis shows the presence of tetragonal phase and EDX analysis establishes inhomogeneous Ag distribution in the grains. The superconducting properties were investigated by fundamental and third harmonic AC magnetic susceptibility. The intergranular critical current determined from AC magnetic susceptibility in the Ag doped sample is several times higher than that in the undoped one, obtained by melting at approximately the same temperatures. Intra-granular current is field independent up to almost 1000 Oe. Using the temperature dependence of third harmonic AC magnetic susceptibility at different DC magnetic fields, the irreversibility lines were obtained for all samples. It is found that Ag addition increased the irreversibility field in comparison with undoped melted and powder sintered samples. All results show that the Ag addition in selenium deficient (FeSe0.94) samples leads to improvement of inter- and intra- granular properties: screening ability, pinning, activation energy and critical current and improves the irreversibility line.
rate research
Read More
We investigated the influence of different Ag additions (up to 10 wt %) on the superconducting properties of FeSe0.94. The structural investigations (XRD and SEM) indicated that Ag is present in three different forms. Ag at grain boundaries supports the excellent intergrain connections and reduces superconducting transition width to values smaller than 1K at B=0 and smaller than 2.74 K at B=14 T. Ag insertion in the crystal lattice unit cell provides additional carriers and changes the electron hole imbalance in FeSe0.94. This results in an increase in the magnetoresistive effect (MR) and critical temperature (Tc). Reacted Ag forms a small amount (~1%) of Ag2Se impurity phase, which may increase the pinning energy in comparison with that of the undoped sample. The enhanced upper critical field (Bc2) is also a result of the increased impurity scattering. Thus, unlike cuprates Ag addition enhances the Tc, Bc2, pinning energy and MR making the properties of polycrystalline FeSe0.94 similar to those of single crystals.
We report enhancement in the magnetic critical current density of indium added polycrystalline SmFeAsO1-xFx. The value of magnetic Jc is around 25 kA/cm2 at 4.2 K under self-magnetic field. Polycrystalline SmFeAsO1-xFx is mainly composed of the superconducting grains and a little of amorphous FeAs compounds. These areas randomly co-exist and amorphous areas are located between superconducting grains. Therefore, the superconducting current is prevented by the amorphous areas. In this study, it is found that indium addition to polycrystalline SmFeAsO1-xFx removes these amorphous areas and induces the bringing together the superconducting grains. It means the total contact surfaces of grains are increased. We suggest that the enhancement of the magnetic critical current density is a direct effect of the indium addition.
We report the superconductivity at enhanced temperature of 5.2 K in the polycrystalline sample of ZrTe3 and Ni intercalated ZrTe3. ZrTe3 is a Charge Density Wave (T = 63K) compound, which is known to superconduct only below 2K in single crystalline form. We discuss that the intergrain strains in the polycrystalline samples induces an intrinsic pressure and thus enhances the transition temperature. Fe intercalation of ZrTe3 kills both the charge density wave and superconducting states, gives rise to the magnetic ordering in the compound.
SmFeAsO1-xFx tapes were prepared using three kinds of starting materials. It shows that the starting materials have an obvious effect on the impurity phases in final superconducting tapes. Compared with the other samples, the samples fabricated by SmAs, FeO, Fe2As, and SmF3 have the smallest arsenide impurity phase and voids. As a result, these samples possess much denser structure and better grain connectivity. Moreover, among the three kinds of samples fabricated in this work, this kind of sample has the highest zero-resistivity temperature ~40 K and largest critical current density ~4600 A/cm^2 in self-field at 4.2 K. This is the highest Jc values reported so far for SmFeAsO1-xFx wires and tapes.
We present the effect of yttrium substitution on superconductivity in the La$_{1-textit{x}}$Y$_{textit{x}}$O$_{0.5}$F$_{0.5}$BiS$_{2}$ system. Polycrystalline samples with nominal Y concentrations up to 40% were synthesized and characterized via electrical resistivity, magnetic susceptibility, and specific heat measurements. Y substitution reduces the lattice parameter textit{a} and unit cell volume textit{V}, and a correlation between the lattice parameter textit{c}, the La-O-La bond angle, and the superconducting critical temperature $T_c$ is observed. The chemical pressure induced by Y substitution for La produces neither the high-$T_c$ superconducting phase nor the structural phase transition seen in LaO$_{0.5}$F$_{0.5}$BiS$_{2}$ under externally applied pressure.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
