Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMicrowave Response of Coaxial Cavities Made of Bulk Magnesium Diboride
417
0
0.0
(
0
)
Added by
Agliolo Gallitto Aurelio
Publication date
2013
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
We report on the microwave (mw) properties of coaxial cavities built by using bulk MgB2 superconductor prepared by reactive liquid Mg infiltration technology. We have assembled a homogeneous cavity, by using an outer MgB2 cylinder and an inner MgB2 rod, and a hybrid cavity by using an outer copper cylinder and the same MgB2 rod as inner conductor. By the analysis of the resonance curves, in the different resonant modes, we have determined the microwave surface resistance, Rs, of the MgB2 materials as a function of the temperature and the frequency, in the absence of DC magnetic fields. At T = 4.2 K and f = 2.5 GHz, by a mw pulsed technique, we have determined the quality factor of the homogeneous cavity as a function of the input power up to a maximum level of about 40 dBm (corresponding to a maximum peak magnetic field of about 100 Oe). Contrary to what occurs in many films, Rs of the MgB2 material used does not exhibit visible variations up to an input power level of about 10 dBm and varies less than a factor of 2 on further increasing the input power of 30 dB.
rate research
Read More
We report on the microwave properties of a resonant cylindrical cavity made of bulk MgB2 superconductor, produced by the reactive liquid Mg infiltration process. The frequency response of the cavity has been measured in the range 5-13GHz. Among the various modes, the TE011, resonating at 9.79GHz, exhibits the highest quality factor. For this mode, we have determined the temperature dependence of the quality factor, obtaining values of the order of 10^5 in the temperature range 4.2-30K. The values of the surface resistance deduced from the measurements of the quality factor agree quite well with those independently measured in a small sample of MgB2 extracted from the same specimen from which the cavity has been obtained.
High energy milling of MgB2 pre-reacted powder renders the material largely amorphous through extreme mechanical deformation and is suitable for mechanically alloying MgB2 with dopants including carbon. Bulk samples of milled C and MgB2 powders subjected to hot isostatic pressing and Mg vapor annealing have achieved critical fields in excess of 32T and critical current density approaching 10^6 A/cm^2.
Magnesium diboride bulk pellets were fabricated from pre-reacted MgB2 powder ball milled with different amounts of exposure to air. Evidence of increased electron scattering including increased resistivity, depressed Tc, and enhanced Hc2 of the milled and heat treated samples were observed as a result of increased contact with air. These and other data were consistent with alloying with carbon as a result of exposure to air. A less clear trend of decreased connectivity associated with air exposure was also observed. In making the case that exposure to air should be considered a doping process, these results may explain the wide varibability of undoped MgB2 properties extant in the literature.
We present results on all-MgB2 tunnel junctions, where the tunnel barrier is deposited MgO or native-oxide of base electrode. For the junctions with MgO, the hysteretic I-V curve resembles a conventional underdamped Josephson junction characteristic with critical current-resistance product nearly independent of the junction area. The dependence of the critical current with temperature up to 20 K agrees with the [Ambegaokar and Baratoff, Phys. Rev. Lett. 10, 486 (1963)] expression. For the junctions with native-oxide, conductance at low bias exhibits subgap features while at high bias reveals thick barriers. As a result no supercurrent was observed in the latter, despite the presence of superconducting-gaps to over 30 K.
The linear and nonlinear response to a microwave electromagnetic field of two c-axis oriented polycrystalline samples of the newly discovered superconductor CaC6 (Tc = 11.5 K) is studied in the superconducting state down to 2 K. The surface resistance Rs and the third order intermodulation distortion, arising from a two-tone excitation, have been measured as a function of temperature and microwave circulating power. Experiments are carried out using a dielectrically loaded copper cavity operating at 7 GHz in a hot finger configuration. The results confirm recent experimental findings that CaC6 behaves as a weakly-coupled, fully gapped, superconductor. The weak power dependence of Rs encourages a further investigation of this novel superconductor as a possible alternative to Nb in specific microwave applications.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
