Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMechanical control of a microrod-resonator optical frequency comb
252
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Robust control and stabilization of optical frequency combs enables an extraordinary range of scientific and technological applications, including frequency metrology at extreme levels of precision, novel spectroscopy of quantum gases and of molecules from visible wavelengths to the far infrared, searches for exoplanets, and photonic waveform synthesis. Here we report on the stabilization of a microresonator-based optical comb (microcomb) by way of mechanical actuation. This represents an important step in the development of microcomb technology, which offers a pathway toward fully-integrated comb systems. Residual fluctuations of our 32.6 GHz microcomb line spacing reach a record stability level of $5times10^{-15}$ for 1 s averaging, thereby highlighting the potential of microcombs to support modern optical frequency standards. Furthermore, measurements of the line spacing with respect to an independent frequency reference reveal the effective stabilization of different spectral slices of the comb with a $<$0.5 mHz variation among 140 comb lines spanning 4.5 THz. These experiments were performed with newly-developed microrod resonators, which were fabricated using a CO$_2$-laser-machining technique.
rate research
Read More
Deformed square resonators with the flat sides replaced by circular sides are proposed and demonstrated to enhance mode Q factors and adjust transverse mode intervals using the regular ray dynamic analysis and numerical simulations. Dual-transverse-mode emissions due to the ultrahigh-Q factors with different wavelength intervals are realized experimentally for AlGaInAs/InP circular-side square microlasers, and the stationary condition of the dual-mode emission is satisfied because the high-Q confined modes have totally different mode numbers. Furthermore, optical frequency combs are generated using the dual-mode lasing microlaser as a seeding light source by cascaded four-wave mixing in a highly nonlinear optical fiber.
Aluminum nitride is an appealing nonlinear optical material for on-chip wavelength conversion. Here we report optical frequency comb generation from high quality factor aluminum nitride micro-ring resonators integrated on silicon substrates. By engineering the waveguide structure to achieve near-zero dispersion at telecommunication wavelengths and optimizing the phase matching for four-wave mixing, frequency combs are generated with a single wavelength continuous-wave pump laser. The Kerr coefficient (n2) of aluminum nitride is further extracted from our experimental results.
Optical frequency combs (OFCs) at Mid-Infrared (MIR) wavelengths are essential for applications in precise spectroscopy, gas sensing and molecular fingerprinting, because of its revolutionary precision in both wavelength and frequency domain. The microresonator-based OFCs make a further step towards practical applications by including such high precision in a compact and cost-effective package. However, dispersion engineering is still a challenge for the conventional chi-3 micro-ring resonators and a MIR pump laser is required. Here we develop a different platform of a chi-2 optical superlattice box resonator to generate MIR OFC by optical parametric down conversion. With near-material-limited quality factor of 2.0*10^7, broadband MIR OFC can be generated with over 250 nm span around 2060 nm, where only a common near-infrared laser is necessary as pump. The fine teeth spacing corresponds to a measurable radio frequency beat note at 1.566 GHz, and also results in a fine spectroscopy resolution. Its linewidth is measured to be 6.1 kHz, which reveals a low comb noise that agrees well with the clean temporal waveforms. With high output power of over 370 mW, such MIR OFC is capable for long distance sensing and ranging applications.
Optical-frequency combs enable measurement precision at the 20th digit, and accuracy entirely commensurate with their reference oscillator. A new direction in experiments is the creation of ultracompact frequency combs by way of nonlinear parametric optics in microresonators. We refer to these as microcombs, and here we report a silicon-chip-based microcomb optical clock that phase-coherently converts an optical-frequency reference to a microwave signal. A low-noise comb spectrum with 25 THz span is generated with a 2 mm diameter silica disk and broadening in nonlinear fiber. This spectrum is stabilized to rubidium frequency references separated by 3.5 THz by controlling two teeth 108 modes apart. The optical clocks output is the electronically countable 33 GHz microcomb line spacing, which features an absolute stability better than the rubidium transitions by the expected factor of 108. Our work demonstrates the comprehensive set of tools needed for interfacing microcombs to state-of-the-art optical clocks.
Optical frequency combs consist of equally spaced discrete optical frequency components and are essential tools for optical communications and for precision metrology, timing and spectroscopy. To date, wide-spanning combs are most often generated by mode-locked lasers or dispersion-engineered resonators with third-order Kerr nonlinearity. An alternative comb generation method uses electro-optic (EO) phase modulation in a resonator with strong second-order nonlinearity, resulting in combs with excellent stability and controllability. Previous EO combs, however, have been limited to narrow widths by a weak EO interaction strength and a lack of dispersion engineering in free-space systems. In this work, we overcome these limitations by realizing an integrated EO comb generator in a thin-film lithium niobate photonic platform that features a large electro-optic response, ultra-low optical loss and highly co-localized microwave and optical felds, while enabling dispersion engineering. Our measured EO frequency comb spans more than the entire telecommunications L-band (over 900 comb lines spaced at ~ 10 GHz), and we show that future dispersion engineering can enable octave-spanning combs. Furthermore, we demonstrate the high tolerance of our comb generator to modulation frequency detuning, with frequency spacing finely controllable over seven orders of magnitude (10 Hz to 100 MHz), and utilize this feature to generate dual frequency combs in a single resonator. Our results show that integrated EO comb generators, capable of generating wide and stable comb spectra, are a powerful complement to integrated Kerr combs, enabling applications ranging from spectroscopy to optical communications.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
