Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTomographic readout of an opto-mechanical interferometer
475
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The quantum state of light changes its nature when being reflected off a mechanical oscillator due to the latters susceptibility to radiation pressure. As a result, a coherent state can transform into a squeezed state and can get entangled with the motion of the oscillator. The complete tomographic reconstruction of the state of light requires the ability to readout arbitrary quadratures. Here we demonstrate such a readout by applying a balanced homodyne detector to an interferometric position measurement of a thermally excited high-Q silicon nitride membrane in a Michelson-Sagnac interferometer. A readout noise of $unit{1.9 cdot 10^{-16}}{metre/sqrt{hertz}}$ around the membranes fundamental oscillation mode at $unit{133}{kilohertz}$ has been achieved, going below the peak value of the standard quantum limit by a factor of 8.2 (9 dB). The readout noise was entirely dominated by shot noise in a rather broad frequency range around the mechanical resonance.
rate research
Read More
We propose to create and detect opto-mechanical entanglement by storing one component of an entangled state of light in a mechanical resonator and then retrieving it. Using micro-macro entanglement of light as recently demonstrated experimentally, one can then create opto-mechanical entangled states where the components of the superposition are macroscopically different. We apply this general approach to two-mode squeezed states where one mode has undergone a large displacement. Based on an analysis of the relevant experimental imperfections, the scheme appears feasible with current technology.
The ability to coherently control mechanical systems with optical fields has made great strides over the past decade, and now includes the use of photon counting techniques to detect the non-classical nature of mechanical states. These techniques may soon be used to perform an opto-mechanical Bell test, hence highlighting the potential of cavity opto-mechanics for device-independent quantum information processing. Here, we propose a witness which reveals opto-mechanical entanglement without any constraint on the global detection efficiencies in a setup allowing one to test a Bell inequality. While our witness relies on a well-defined description and correct experimental calibration of the measurements, it does not need a detailed knowledge of the functioning of the opto-mechanical system. A feasibility study including dominant sources of noise and loss shows that it can readily be used to reveal opto-mechanical entanglement in present-day experiments with photonic crystal nanobeam resonators.
Realizing optical manipulation of microscopic objects is crucial in the research fields of life science, condensed matter physics and physical chemistry. In non-liquid environments, this task is commonly regarded as difficult due to strong adhesive surface force ($simmurm N$) between solid interfaces that makes tiny optical driven force ($simrm pN$) insignificant. Here, by recognizing the microscopic interaction mechanism between friction force -- the parallel component of surface force on the contact surface -- and thermoelastic waves induced by pulsed optical absorption, we establish a general principle enabling the actuation of micro-objects on dry frictional surfaces based on the opto-thermo-mechanical effects. Theoretically, we predict that nanosecond pulsed optical absorption with mW-scale peak power is sufficient to tame $murm N$-scale friction force. Experimentally, we demonstrate that two-dimensional spiral motion of gold plates on micro-fibers driven by a nanosecond pulsed laser, and reveal the specific rules of motion control. Our results pave the way for future development of micro-scale actuators in nonliquid environments.
We propose a scheme to realize quantum networking of superconducting qubits based on the opto-mechanical interface. The superconducting qubits interact with the microwave photons, which then couple to the optical photons through the opto-mechanical interface. The interface generates a quantum link between superconducting qubits and optical flying qubits with tunable pulse shapes and carrier frequencies, enabling transmission of quantum information to other superconducting or atomic qubits. We show that the scheme works under realistic experimental conditions and it also provides a way for fast initialization of the superconducting qubits under 1 K instead of 20 mK operation temperature.
We show how to apply the Leggett-Garg inequality to opto-electro-mechanical systems near their quantum ground state. We find that by using a dichotomic quantum non-demolition measurement (via, e.g., an additional circuit-QED measurement device) either on the cavity or on the nanomechanical system itself, the Leggett-Garg inequality is violated. We argue that only measurements on the mechanical system itself give a truly unambigous violation of the Leggett-Garg inequality for the mechanical system. In this case, a violation of the Leggett-Garg inequality indicates physics beyond that of macroscopic realism is occurring in the mechanical system. Finally, we discuss the difficulties in using unbound non-dichotomic observables with the Leggett-Garg inequality.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
