Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userHigh-power broadband laser source tunable from 3.0 um to 4.4 um based on a femtosecond Yb:fiber oscillator
126
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We describe a tunable broadband mid-infrared laser source based on difference-frequency mixing of a 100 MHz femtosecond Yb:fiber laser oscillator and a Raman-shifted soliton generated with the same laser. The resulting light is tunable over 3.0 um to 4.4 um, with a FWHM bandwidth of 170 nm and maximum average output power up to 125 mW. The noise and coherence properties of this source are also investigated and described.
rate research
Read More
In this work, we present a high pulse energy multi-wavelength Raman laser spanning from 1.53 um up to 2.4 um by employing the cascaded rotational stimulated Raman scattering (SRS) effect in a 5-m hydrogen (H2) -filled nested anti-resonant fiber (NARF), pumped by a linearly polarized Er/Yb fiber laser with a peak power of ~13 kW and pulse duration of ~7 ns in the C-band. The developed Raman laser has distinct lines at 1683 nm, 1868 nm, 2100 nm, and 2400 nm, with pulse energies as high as 18.25 uJ, 14.4 uJ, 14.1 uJ, and 8.2 uJ, respectively. We demonstrate how the energy in the Raman lines can be controlled by tuning the H2 pressure from 1 bar to 20 bar
Continuous-wave mode-locked femtosecond 2 um solid-state laser with a c-cut Tm:CaYAlO4 as gain medium was experimentally demonstrated. The mode locked laser generated stable pulses with average output power as high as 531 mW, pulse duration of 496 fs, and repetition rate of 97 MHz at 1975 nm. The research results show that Tm:CaYAlO4 is an excellent gain medium for femtosecond pulse generation at 2um wavelength.
In this paper, a technique combing cascaded energy-transfer pumping (CEP) method and master-oscillator power-amplifier (MOPA) configuration is proposed for power scaling of 1.6-um-band single-frequency fiber lasers (SFFLs), where the Er3+ ion has a limited gain. The CEP technique is fulfilled by coupling a primary signal light at 1.6 um and a C-band auxiliary laser. The numerical model of the fiber amplifier with the CEP technique reveals that the energy transfer process involves the pump competition and the in-band particle transition between the signal and auxiliary lights. Moreover, for the signal emission, the population density in the upper level is enhanced and the effective population inversion is achieved due to the CEP. A single-frequency MOPA laser at 1603 nm with an output power of 52.6 W is obtained experimentally. Besides, a slope efficiency of 30.4% is improved by more than 10% through the CEP technique. Both the output power and slope efficiency are by far the highest for 1.6-um-band SFFLs. Meanwhile, a laser linewidth of 5.2 kHz and a polarization-extinction ratio of ~18 dB are obtained at the maximum output power. The proposed technique provides an optional method of increasing the slope efficiency and power scaling for fiber lasers operating at L-band.
In this letter, we present a high pulse energy Raman laser at 1946 nm wavelength directly pumped with a 1533 nm custom-made fiber laser. The Raman laser is based on the stimulated Raman scattering (SRS) in an 8-meter carbon dioxide (CO2) filled nested anti-resonant hollow-core fiber (ARHCF). The low energy phonon emission combined with the inherent SRS process along the low-loss fiber allows the generation of high pulse energy up to 15.4 {mu}J at atmospheric CO2 pressure. The Raman laser exhibits good long-term stability and low relative intensity noise (RIN) of less than 4%. We also investigate the pressure-dependent overlap of the Raman laser line with the absorption band of CO2 at 2 {mu}m spectral range. Our results constitute a novel and promising technology towards high energy 2 {mu}m lasers.
We demonstrate a fiber system which amplifies and compresses pulses from a gain-switched diode. A Mamyshev regenerator shortens the pulses and improves their coherence, enabling subsequent amplification by parabolic pre-shaping. As a result, we are able to control nonlinear effects and generate nearly transform-limited, 140-fs pulses with 13-MW peak power---an order-of-magnitude improvement over previous gain-switched diode sources. Seeding with a gain-switched diode results in random fluctuations of 2% in the pulse energy, which future work using known techniques may ameliorate. Further development may allow such systems to compete directly with sources based on modelocked oscillators in some applications while enjoying unparalleled robustness and repetition rate control.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
