Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userProbing the micromechanics of a multi-contact interface at the onset of frictional sliding
233
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Digital Image Correlation is used to study the micromechanics of a multi-contact interface formed between a rough elastomer and a smooth glass surface. The in-plane elastomer deformation is monitored during the incipient sliding regime, i.e. the transition between static and sliding contact. As the shear load is increased, an annular slip region, in coexistence with a central stick region, is found to progressively invade the contact. From the interfacial displacement field, the tangential stress field can be further computed using a numerical inversion procedure. These local mechanical measurements are found to be correctly captured by Cattaneo and Mindlin (CM)s model. However, close comparison reveals significant discrepancies in both the displacements and stress fields that reflect the oversimplifying hypothesis underlying CMs scenario. In particular, our optical measurements allow us to exhibit an elasto-plastic like friction constitutive equation that differs from the rigid-plastic behavior assumed in CMs model. This local constitutive law, which involves a roughness-related length scale, is consistent with the model of Bureau textit{et al.} [Proc. R. Soc. London A textbf{459}, 2787 (2003)] derived for homogeneously loaded macroscopic multi-contact interfaces, thus extending its validity to mesoscopic scales.measurements allow for the first quantitative test of Cattaneo and Mindlin (CM) classical model of the incipient sliding of a smooth interface. Small deviations are observed and interpreted as a result of the finite compliance of the rough interface, a behavior which contrasts with Amontons law of friction assumed to be valid locally in CMs model. We illustrate how these measurements actually provide a method for probing the rheology of the rough interface, which we find to be of the elasto-plastic type.
rate research
Read More
A MEMS-based sensing device is used to measure the normal and tangential stress fields at the base of a rough elastomer film in contact with a smooth glass cylinder in steady sliding. This geometry allows for a direct comparison between the stress profiles measured along the sliding direction and the predictions of an original textit{exact} bidimensional model of friction. The latter assumes Amontons friction law, which implies that in steady sliding the interfacial tangential stress is equal to the normal stress times a pressure-independent dynamic friction coefficient $mu_d$, but makes no further assumption on the normal stress field. Discrepancy between the measured and calculated profiles is less than 14% over the range of loads explored. Comparison with a test model, based on the classical assumption that the normal stress field is unchanged upon tangential loading, shows that the exact model better reproduces the experimental profiles at high loads. However, significant deviations remain that are not accounted for by either calculations. In that regard, the relevance of two other assumptions made in the calculations, namely (i) the smoothness of the interface and (ii) the pressure-independence of $mu_d$ is briefly discussed.
We analyze the local structure of two dimensional packings of frictional disks numerically. We focus on the fractions x_i of particles that are in contact with i neighbors, and systematically vary the confining pressure p and friction coefficient mu. We find that for all mu, the fractions x_i exhibit powerlaw scaling with p, which allows us to obtain an accurate estimate for x_i at zero pressure. We uncover how these zero pressure fractions x_i vary with mu, and introduce a simple model that captures most of this variation. We also probe the correlations between the contact numbers of neighboring particles.
We perform real-time measurements of the net contact area between two blocks of like material at the onset of frictional slip. We show that the process of interface detachment, which immediately precedes the inception of frictional sliding, is governed by three different types of detachment fronts. These crack-like detachment fronts differ by both their propagation velocities and by the amount of net contact surface reduction caused by their passage. The most rapid fronts propagate at intersonic velocities but generate a negligible reduction in contact area across the interface. Sub-Rayleigh fronts are crack-like modes which propagate at velocities up to the Rayleigh wave speed, VR, and give rise to an approximate 10% reduction in net contact area. The most efficient contact area reduction (~20%) is precipitated by the passage of slow detachment fronts. These fronts propagate at anomalously slow velocities, which are over an order of magnitude lower than VR yet orders of magnitude higher than other characteristic velocity scales such as either slip or loading velocities. Slow fronts are generated, in conjunction with intersonic fronts, by the sudden arrest of sub-Rayleigh fronts. No overall sliding of the interface occurs until either of the slower two fronts traverses the entire interface, and motion at the leading edge of the interface is initiated. Slip at the trailing edge of the interface accompanies the motion of both the slow and sub-Rayleigh fronts. We might expect these modes to be important in both fault nucleation and earthquake dynamics.
We study the micromechanics of collagen-I gel with the goal of bridging the gap between theory and experiment in the study of biopolymer networks. Three-dimensional images of fluorescently labeled collagen are obtained by confocal microscopy and the network geometry is extracted using a 3d network skeletonization algorithm. Each fiber is modeled as a worm-like-chain that resists stretching and bending, and each cross-link is modeled as torsional spring. The stress-strain curves of networks at three different densities are compared to rheology measurements. The model shows good agreement with experiment, confirming that strain stiffening of collagen can be explained entirely by geometric realignment of the network, as opposed to entropic stiffening of individual fibers. The model also suggests that at small strains, cross-link deformation is the main contributer to network stiffness whereas at large strains, fiber stretching dominates. Since this modeling effort uses networks with realistic geometries, this analysis can ultimately serve as a tool for understanding how the mechanics of fibers and cross-links at the microscopic level produce the macroscopic properties of the network. While the focus of this paper is on the mechanics of collagen, we demonstrate a framework that can be applied to many biopolymer networks.
The effect of thermal fluctuations near a contact line of a liquid interface partially wetting an impenetrable substrate is studied analytically and numerically. Promoting both the interface profile and the contact line position to random variables, we explore the equilibrium properties of the corresponding fluctuating contact line problem based on an interfacial Hamiltonian involving a contact binding potential. To facilitate an analytical treatment we consider the case of a one-dimensional interface. The effective boundary condition at the contact line is determined by a dimensionless parameter that encodes the relative importance of thermal energy and substrate energy at the microscopic scale. We find that this parameter controls the transition from a partially wetting to a pseudo-partial wetting state, the latter being characterized by a thin prewetting film of fixed thickness. In the partial wetting regime, instead, the profile typically approaches the substrate via an exponentially thinning prewetting film. We show that, independently of the physics at the microscopic scale, Youngs angle is recovered sufficiently far from the substrate. The fluctuations of the interface and of the contact line give rise to an effective disjoining pressure, exponentially decreasing with height. Fluctuations therefore provide a regularization of the singular contact forces occurring in the corresponding deterministic problem.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
