Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userConductance of p-n-p graphene structures with air-bridge top gates
194
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We have fabricated graphene devices with a top gate separated from the graphene layer by an air gap--a design which does not decrease the mobility of charge carriers under the gate. This gate is used to realise p-n-p structures where the conducting properties of chiral carriers are studied. The band profile of the structures is calculated taking into account the specifics of the graphene density of states and is used to find the resistance of the p-n junctions expected for chiral carriers. We show that ballistic p-n junctions have larger resistance than diffusive ones. This is caused by suppressed transmission of chiral carriers at angles away from the normal to the junction.
rate research
Read More
We developed a multi-level lithography process to fabricate graphene p-n-p junctions with the novel geometry of contactless, suspended top gates. This fabrication procedure minimizes damage or doping to the single atomic layer, which is only exposed to conventional resists and developers. The process does not require special equipment for depositing gate dielectrics or releasing sacrificial layers, and is compatible with annealing procedures that improve device mobility. Using this technique, we fabricate graphene devices with suspended local top gates, where the creation of high quality graphene p-n-p junctions is confirmed by transport data at zero and high magnetic fields.
We study the processes of the electron and hole injection (double injection) into the i-region of graphene-layer and multiple graphene-layer p-i-n structures at the forward bias voltages. The hydrodynamic equations governing the electron and hole transport in graphene coupled with the two-dimensional Poisson equation are employed. Using analytical and numerical solutions of the equations of the model, we calculate the band edge profile, the spatial distributions of the quasi-Fermi energies, carrier density and velocity, and the current-voltage characteristics. In particular, we demonstrated that the electron and hole collisions can strongly affect these distributions. The obtained results can be used for the realization and optimization of graphene-based injection terahertz and infrared lasers.
We report on the fabrication and transport studies of a single-layer graphene p-n junction. Carrier type and density in two adjacent regions are individually controlled by electrostatic gating using a local top gate and a global back gate. A functionalized Al203 oxide that adheres to graphene and does not significantly affect its electronic properties is described. Measurements in the quantum Hall regime reveal new plateaus of two-terminal conductance across the junction at 1 and 3/2 times the quantum of conductance, e2/h, consistent with theory.
Using low-temperature high-magnetic-field scanning tunneling microscopy and spectroscopy (STM/STS), we systematically study a graphene quantum dot (GQD) defined by a circular graphene p-p junction. Inside the GQD, we observe a series of quasi-bound states arising from whispering-gallery-mode (WGM) confinement of the circular junction and directly visualize these quasi-bound states down to atomic dimensions. By applying a strong magnetic field, a large jump in energy of the quasi-bound states, which is about one-half the energy spacing between the quasi-bound states, is observed. Such a behavior results from turning on a {pi} Berry phase of massless Dirac fermions in graphene by a magnetic field. Moreover, our experiment demonstrates that a quasi-bound state splits into two peaks with an energy separation of about 26 meV when the Fermi level crosses the quasi-bound state, indicating that there are strong electron-electron interactions in the GQD.
We demonstrate high-frequency mechanical resonators in ballistic graphene p-n junctions. Fully suspended graphene devices with two bottom gates exhibit ballistic bipolar behavior after current annealing. We determine the graphene mass density and built-in tension for different current annealing steps by comparing the measured mechanical resonant response to a simplified membrane model. We consistently find that after the last annealing step the mass density compares well with the expected density of pure graphene. In a graphene membrane with high built-in tension, but still of macroscopic size with dimensions 3 $times$ 1 $mu m^{2}$, a record resonance frequency of 1.17 GHz is observed after the final current annealing step. We further compare the resonance response measured in the unipolar with the one in the bipolar regime. Remarkably, the resonant signals are strongly enhanced in the bipolar regime. This enhancement is caused in part by the Fabry-Perot resonances that appear in the bipolar regime and possibly also by the photothermoelectric effect that can be very pronounced in graphene p-n junctions under microwave irradiation.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
