Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDirect Numerical Simulation of a separated channel flow with a smooth profile
156
0
0.0
(
0
)
Added by
Jean-Philippe Laval
Publication date
2007
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
A direct numerical simulation (DNS) of a channel flow with one curved surface was performed at moderate Reynolds number (Re_tau = 395 at the inlet). The adverse pressure gradient was obtained by a wall curvature through a mathematical mapping from physical coordinates to Cartesian ones. The code, using spectral spanwise and normal discretization, combines the advantage of a good accuracy with a fast integration procedure compared to standard numerical procedures for complex geometries. The turbulent flow slightly separates on the profile at the lower curved wall and is at the onset of separation at the opposite flat wall. The thin separation bubble is characterized with a reversal flow fraction. Intense vortices are generated near the separation line on the lower wall but also at the upper wall. Turbulent normal stresses and kinetic energy budget are investigated along the channel.
rate research
Read More
Sand traps are used to measure Aeolian flux. Since they modify the surrounding wind velocity field their gauging represents an important challenge. We use numerical simulations under the assumption of homogeneous turbulence based on FLUENT to systematically study the flow field and trapping efficiency of one of the most common devices based on a hollow cylinder with two slits. In particular, we investigate the dependence on the wind speed, the Stokes number, the permeability of the membrane on the slit and the saltation height.
Turbulent flows under transcritical conditions are present in regenerative cooling systems of rocker engines and extraction processes in chemical engineering. The turbulent flows and the corresponding heat transfer phenomena in these complex processes are still not well understood experimentally and numerically. The objective of this work is to investigate the turbulent flows under transcritical conditions using DNS of turbulent channel flows. A fully compressible solver is used in conjunction with a Peng-Robinson real-fluid equation of state to describe the transcritical flows. A channel flow with two isothermal walls is simulated with one heated and one cooled boundary layers. The grid resolution adopted in this study is slightly finer than that required for DNS of incompressible channel flows. The simulations are conducted using both fully (FC) and quasi-conservative (QC) schemes to assess their performance for transcritical wall-bounded flows. The instantaneous flows and the statistics are analyzed and compared with the canonical theories. It is found that results from both FC and QC schemes qualitatively agree well with noticeable difference near the top heated wall, where spurious oscillations in velocity can be observed. Using the DNS data, we then examine the usefulness of Townsend attached eddy hypothesis in the context of flows at transcritical conditions. It is shown that the streamwise energy spectrum exhibits the inverse wavenumber scaling and that the streamwise velocity structure function follows a logarithmic scaling, thus providing support to the attached eddy model at transcritical conditions.
Rod bundle flows are commonplace in nuclear engineering, and are present in light water reactors (LWRs) as well as other more advanced concepts. Inhomogeneities in the bundle cross section can lead to complex flow phenomena, including varying local conditions of turbulence. Despite the decades of numerical and experimental investigations regarding this topic, and the importance of elucidating the physics of the flow field, to date there are few publicly available direct numerical simulations (DNS) of the flow in multiple-pin rod bundles. Thus a multiple-pin DNS study can provide significant value toward reaching a deeper understanding of the flow physics, as well as a reference simulation for development of various reduced-resolution analysis techniques. To this end, DNS of the flow in a square 5x5 rod bundle at Reynolds number of 19,000 has been performed using the highly-parallel spectral element code Nek5000. The geometrical dimensions were representative of typical LWR fuel designs. The DNS was designed using microscales estimated from an advanced Reynolds-Averaged Navier-Stokes (RANS) model. Characteristics of the velocity field, Reynolds stresses, and anisotropy are presented in detail for various regions of the bundle. The turbulent kinetic energy budget is also presented and discussed
Rod bundle flows are prevalent in nuclear engineering for both light water reactors (LWR) and advanced reactor concepts. Unlike canonical channel flow, the flow in rod bundles presents some unique characteristics, notably due to the inhomogeneous cross section which can present different local conditions of turbulence as well as localized effects characteristic of external flows. Despite the ubiquity of rod bundle flows and the decades of experimental and numerical knowledge acquired in this field, there are no publicly available direct numerical simulations (DNS) of the flow in multiple pin rod bundles with heat transfer. A multiple pin DNS study is of great value as it would allow for assessment of the reliability of various turbulence models in the presence of heat transfer, as well as allow for a deeper understanding of the flow physics. We present work towards DNS of the flow in a square 5x5 rod bundle representative of LWR fuel. We consider standard configurations as well as configurations where the central pin is replaced with a guide thimble. We perform simulations in STAR-CCM+ to design the numerical DNS, which is to be conducted using the open source spectral element code Nek5000. Large Eddy Simulations are also performed in Nek5000 to confirm that the resolution requirements are adequate. We compare results from STAR-CCM+ and Nek5000, which show very good agreement in the wide gaps with larger discrepancies in the narrow gaps. In particular, evidence of a gap vortex street is seen in the edge subchannels in LES but is not predicted by STAR-CCM+.
The turbulent boundary layer over a Gaussian shaped bump is computed by direct numerical simulation (DNS) of the incompressible Navier-Stokes equations. The two-dimensional bump causes a series of strong pressure gradients alternating in rapid succession. At the inflow, the momentum thickness Reynolds number is approximately 1,000 and the boundary layer thickness is 1/8 of the bump height. DNS results show that the strong favorable pressure gradient (FPG) causes the boundary layer to enter a relaminarization process. The near-wall turbulence is significantly weakened and becomes intermittent, however relaminarization does not complete. The streamwise velocity profiles deviate above the standard logarithmic law and the Reynolds shear stress is reduced. The strong acceleration also suppresses the wall-shear normalized turbulent kinetic energy production rate. At the bump peak, where the FPG switches to an adverse gradient (APG), the near-wall turbulence is suddenly enhanced through a partial retransition process. This results in a new highly energized internal layer which is more resilient to the strong APG and only produces incipient flow separation on the downstream side. In the strong FPG and APG regions, the inner and outer layers become largely independent of each other. The near-wall region responds to the pressure gradients and determines the skin friction. The outer layer behaves similarly to a free-shear layer subject to pressure gradients and mean streamline curvature effects. Results from a RANS simulation of the bump are also discussed and clearly show the lack of predictive capacity of the near-wall pressure gradient effects on the mean flow.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
