Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userThe autoignition of cyclopentane and cyclohexane in a shock tube
196
0
0.0
(
0
)
Authors
Baptiste Sirjean
Ask ChatGPT about the research
No Arabic abstract
Ignition delay times of cyclohexane-oxygen-argon and cyclopentane-oxygen-argon mixtures have been measured in a shock tube, the onset of ignition being detected by OH radical emission. Mixtures contained 0.5 or 1 % of hydrocarbon for equivalence ratios ranging from 0.5 to 2. Reflected shock waves allowed temperatures from 1230 to 1800 K and pressures from 7.3 to 9.5 atm to be obtained. These measurements have shown that cyclopentane is much less reactive than cyclohexane, as for a given temperature the observed autoignition delay times were about ten times higher for the C5 compound compared to the C6. Detailed mechanisms for the combustion of cyclohexane and cyclopentane have been proposed to reproduce these results. The elementary steps included in the kinetic models of the oxidation of cyclanes are close to those proposed to describe the oxidation of acyclic alkanes and alkenes. Consequently, it has been possible to obtain these models by using an improved version of software EXGAS, a computer package developed to perform the automatic generation of detailed kinetic models for the gas-phase oxidation and combustion of linear and branched alkanes and alkenes. Nevertheless, the modelling of the oxidation of cyclanes requires to consider new types of generic reactions, and especially to define new correlations for the estimation of the rate constants. Ab initio calculations have been used to better know some of the rate constants used in the case of cyclopentane. The main reaction pathways have been derived from flow rate and sensitivity analyses.
rate research
Read More
This paper presents a modeling study of the oxidation of cyclohexane from low to intermediate temperature (650-1050 K), including the negative temperature coefficient (NTC) zone. A detailed kinetic mechanism has been developed using computer-aided generation. This comprehensive low-temperature mechanism involves 513 species and 2446 reactions and includes two additions of cyclohexyl radicals to oxygen, as well as subsequent reactions. The rate constants of the reactions involving the formation of bicyclic species (isomerizations, formation of cyclic ethers) have been evaluated from literature data. This mechanism is able to satisfactorily reproduce experimental results obtained in a rapid-compression machine for temperatures ranging from 650 to 900 K and in a jet-stirred reactor from 750 to 1050 K. Flow-rate analyses have been performed at low and intermediate temperatures.
Methyl valerate (C$_6$H$_{12}$O$_2$, methyl pentanoate) is a methyl ester and a relevant surrogate component for biodiesel. In this work, we present ignition delays of methyl valerate measured using a rapid compression machine at a range of engine-relevant temperature, pressure, and equivalence ratio conditions. The conditions we have studied include equivalence ratios from 0.25 to 2.0, temperatures between 680 K and 1050 K, and pressures of 15 bar and 30 bar. The ignition delay data demonstrate a negative temperature coefficient region in the temperature range of 720 K-800 K for both $phi$=2.0, 15 bar and $phi$=1.0, 30 bar, with two-stage ignition apparent over the narrower temperature ranges of 720 K-760 K for the lower pressure and 740 K-800 K at the higher pressure. In addition, the experimental ignition delay data are compared with simulations using an existing chemical kinetic model from the literature. The simulations with the literature model under-predict the data by factors between 2 and 10 over the entire range of the experimental data. To help determine the possible reasons for the discrepancy between simulations and experiments, a new chemical kinetic model is developed using the Reaction Mechanism Generator (RMG) software. The agreement between the experimental data and the RMG model is improved but still not satisfactory. Directions for future improvement of the methyl valerate model are discussed.
Autoignition delay experiments for the isomers of butanol, including n-, sec-, tert-, and iso-butanol, have been performed using a heated rapid compression machine. For a compressed pressure of 15 bar, the compressed temperatures have been varied in the range of 725-855 K for all the stoichiometric fuel/oxidizer mixtures. Over the conditions investigated in this study, the ignition delay decreases monotonically as temperature increases and exhibits single-stage characteristics. Experimental ignition delays are also compared to simulations computed using three kinetic mechanisms available in the literature. Reasonable agreement is found for three isomers (tert-, iso-, and n-butanol).
Autoignition experiments for n-butanol have been performed using a heated rapid compression machine at compressed pressures of 15 and 30 bar, in the compressed temperature range of 675-925 K, and for equivalence ratios of 0.5, 1.0, and 2.0. Over the conditions studied, the ignition delay decreases monotonically as temperature increases, and the autoignition response exhibits single-stage characteristics. A non-linear fit to the experimental data is performed and the reactivity, in terms of the inverse of ignition delay, shows nearly second order dependence on the initial oxygen mole fraction and slightly greater than first order dependence on initial fuel mole fraction and compressed pressure. Experimentally measured ignition delays are also compared to simulations using several reaction mechanisms available in the literature. Agreement between simulated and experimental ignition delay is found to be unsatisfactory. Sensitivity analysis is performed on one recent mechanism and indicates that uncertainties in the rate coefficients of parent fuel decomposition reactions play a major role in causing the poor agreement. Path analysis of the fuel decomposition reactions supports this conclusion and also highlights the particular importance of certain pathways. Further experimental investigations of the fuel decomposition, including speciation measurements, are required.
The electronic properties of interfaces can depend on their isotopic constitution. One known case is that of cyclohexane physisorbed on Rh(111), in which isotope effects have been measured on the work function change and desorption energies. These effects can only be captured by calculations including nuclear quantum effects (NQE). In this paper, this interface is addressed employing dispersion-inclusive density-functional theory coupled to a quasi-harmonic (QH) approximation for NQE, as well as to fully anharmonic ab initio path integral molecular dynamics (PIMD). The QH approximation is able to capture that deuterated cyclohexane has a smaller adsorption energy and lies about 0.01 A farther from the Rh(111) surface than its isotopologue, which can be correlated to the isotope effect in the work function change. An investigation of the validity of the QH approximation relying on PIMD simulations, leads to the conclusion that although this interface is highly impacted by anharmonic quantum fluctuations in the molecular layer and at bonding sites, these anharmonic contributions play a minor role when analysing isotope effects at low temperatures. Nevertheless, anharmonic quantum fluctuations cause an increase in the distance between the molecular layer and Rh(111), a consequent smaller overall work function change, and intricate changes in orbital hybridization.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
