اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدPower Beacon Placement for Maximizing Guaranteed Coverage in Bistatic Backscatter Networks
122
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The bistatic backscatter architecture, with its extended range, enables flexible deployment opportunities for backscatter devices. In this paper, we study the placement of power beacons (PBs) in bistatic backscatter networks to maximize the guaranteed coverage distance (GCD), defined as the distance from the reader within which backscatter devices are able to satisfy a given quality-of-service constraint. This work departs from conventional energy source placement problems by considering the performance of the additional backscatter link on top of the energy transfer link. We adopt and optimize a symmetric PB placement scheme to maximize the GCD. The optimal PB placement under this scheme is obtained using either analytically tractable expressions or an efficient algorithm. Numerical results provide useful insights into the impacts of various system parameters on the PB placement and the resulting GCD, plus the advantages of the adopted symmetric placement scheme over other benchmark schemes.
قيم البحث
اقرأ أيضاً
Existing tag signal detection algorithms inevitably suffer from a high bit error rate (BER) due to the difficulties in estimating the channel state information (CSI). To eliminate the requirement of channel estimation and to improve the system perfor
mance, in this paper, we adopt a deep transfer learning (DTL) approach to implicitly extract the features of communication channel and directly recover tag symbols. Inspired by the powerful capability of convolutional neural networks (CNN) in exploring the features of data in a matrix form, we design a novel covariance matrix aware neural network (CMNet)-based detection scheme to facilitate DTL for tag signal detection, which consists of offline learning, transfer learning, and online detection. Specifically, a CMNet-based likelihood ratio test (CMNet-LRT) is derived based on the minimum error probability (MEP) criterion. Taking advantage of the outstanding performance of DTL in transferring knowledge with only a few training data, the proposed scheme can adaptively fine-tune the detector for different channel environments to further improve the detection performance. Finally, extensive simulation results demonstrate that the BER performance of the proposed method is comparable to that of the optimal detection method with perfect CSI.
Bistatic backscatter communication (BackCom) allows passive tags to transmit over extended ranges, but at the cost of having carrier emitters either transmitting at high powers or being deployed very close to tags. In this paper, we examine how the p
resence of an intelligent reflecting surface (IRS) could benefit the bistatic BackCom system. We study the transmit power minimization problem at the carrier emitter, where its transmit beamforming vector is jointly optimized with the IRS phase shifts, whilst guaranteeing a required BackCom performance. A unique feature in this system setup is the multiple IRS reflections experienced by signals traveling from the carrier emitter to the reader, which renders the optimization problem highly nonconvex. Therefore, we propose algorithms based on the minorization-maximization and alternating optimization techniques to obtain approximate solutions for the joint design. We also propose low-complexity algorithms based on successive optimization of individual phase shifts. Our results reveal considerable transmit power savings in both single-tag and multi-tag systems, even with moderate IRS sizes, which may be translated to significant range improvements using the original transmit power or reduce the reliance of tags on carrier emitters located at close range.
The Fourth Industrial Revolution (Industrial 4.0) is coming, and this revolution will fundamentally enhance the way the factories manufacture products. The conventional wired lines connecting central controller to robots or actuators will be replaced
by wireless communication networks due to its low cost of maintenance and high deployment flexibility. However, some critical industrial applications require ultra-high reliability and low latency communication (URLLC). In this paper, we advocate the adoption of massive multiple-input multiple output (MIMO) to support the wireless transmission for industrial applications as it can provide deterministic communications similar as wired lines thanks to its channel hardening effects. To reduce the latency, the channel blocklength for packet transmission is finite, and suffers from transmission rate degradation and decoding error probability. Thus, conventional resource allocation for massive MIMO transmission based on Shannon capacity assuming the infinite channel blocklength is no longer optimal. We first derive the closed-form expression of lower bound (LB) of achievable uplink data rate for massive MIMO system with imperfect channel state information (CSI) for both maximum-ratio combining (MRC) and zero-forcing (ZF) receivers. Then, we propose novel low-complexity algorithms to solve the achievable data rate maximization problems by jointly optimizing the pilot and payload transmission power for both MRC and ZF. Simulation results confirm the rapid convergence speed and performance advantage over the existing benchmark algorithms.
The scarcity of spectrum resources in current wireless communication systems has sparked enormous research interest in the terahertz (THz) frequency band. This band is characterized by fundamentally different propagation properties resulting in diffe
rent interference structures from what we have observed so far at lower frequencies. In this paper, we derive a new expression for the coverage probability of downlink transmission in THz communication systems within a three-dimensional (3D) environment. First, we establish a 3D propagation model which considers the molecular absorption loss, 3D directional antennas at both access points (APs) and user equipments (UEs), interference from nearby APs, and dynamic blockages caused by moving humans. Then, we develop a novel easy-to-use analytical framework based on the dominant interferer analysis to evaluate the coverage probability, the novelty of which lies in the incorporation of the instantaneous interference and the vertical height of THz devices. Our numerical results demonstrate the accuracy of our analysis and reveal that the coverage probability significantly decreases when the transmission distance increases. We also show the increasing blocker density and increasing AP density impose different impacts on the coverage performance when the UE-AP link of interest is in line-of-sight. We further show that the coverage performance improvement brought by increasing the antenna directivity at APs is higher than that brought by increasing the antenna directivity at UEs.
Unmanned aerial vehicles (UAVs), as aerial base stations, are a promising solution for providing wireless communications, thanks to their high flexibility and autonomy. Moreover, emerging services, such as extended reality, require high-capacity comm
unications. To achieve this, millimeter wave (mmWave), and recently, terahertz bands have been considered for UAV communications. However, communication at these high frequencies requires a line-of-sight (LoS) to the terminals, which may be located in 3D space and may have extremely limited direct-line-of-view (LoV) due to blocking objects, like buildings and trees. In this paper, we investigate the problem of determining 3D placement and orientation of UAVs such that users have guaranteed LoS coverage by at least one UAV and the signal-to-noise ratio (SNR) between the UAV-user pairs are maximized. We formulate the problem as an integer linear programming(ILP) problem and prove its NP-hardness. Next, we propose a low-complexity geometry-based greedy algorithm to solve the problem efficiently. Our simulation results show that the proposed algorithm (almost) always guarantees LoS coverage to all users in all considered simulation settings.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
