اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدGrowth of carbon nanotubes on quasicrystalline alloys
99
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report on the synthesis of carbon nanotubes on quasicrystalline alloys. Aligned multiwalled carbon nanotubes (MWNTs) on the conducting faces of decagonal quasicrystals were synthesized using floating catalyst chemical vapor deposition. The alignment of the nanotubes was found perpendicular to the decagonal faces of the quasicrystals. A comparison between the growth and tube quality has also been made between tubes grown on various quasicrystalline and SiO2 substrates. While a significant MWNT growth was observed on decagonal quasicrystalline substrate, there was no significant growth observed on icosahedral quasicrystalline substrate. Raman spectroscopy and high resolution transmission electron microscopy (HRTEM) results show high crystalline nature of the nanotubes. Presence of continuous iron filled core in the nanotubes grown on these substrates was also observed, which is typically not seen in MWNTs grown using similar process on silicon and/or silicon dioxide substrates. The study has important implications for understanding the growth mechanism of MWNTs on conducting substrates which have potential applications as heat sinks.
قيم البحث
اقرأ أيضاً
Double-walled carbon nanotubes (DWCNTs) combined the advantages of multi-walled (MW-) and single-walled (SW-) CNTs can be obtained by transforming the precursors (e.g. fullerene, ferrocene) into thin inner CNTs inside SWCNTs as templates. However, th
is method is limited since the DWCNT yield is strongly influenced by the filling efficiency (depending on the type of the filled molecules), opening and cutting the SWCNTs, and the diameter of the host SWCNTs. Therefore, it cannot be applied to all types of SWCNT templates. Here we show a universal route to synthesize ultra-thin DWCNTs via making SWCNTs stable at high temperature in vacuum. This method applies to different types of SWCNTs including metallicity-sorted ones without using any precursors since the carbon sources were from the reconstructed SWCNTs and the residue carbons. The resulting DWCNTs are with high quality and the yield of inner tubes is comparable to/higher than that of the DWCNTs made from the transformation of ferrocene/fullerene peapods.
The Raman response of new structures grown after filling SWCNTs with ferrocene and transformation at moderate high temperatures is demonstrated to be very strong, even stronger than the response from the tubes. Transmission electron microscopy demons
trates that the new objects are flat and exhibit a structure similar to short fragments of nanoribbons. The growth process is controlled by two different activation energies for low and high transformation temperatures, respectively. Immediately after filling Raman pattern from a precursor molecule are detected. Two different types of nanoribbons were identified by selecting special laser energies for the Raman excitation. These ribbons have the signature of quaterrylene and terrylene, respectively.
Poly(ethylene imine) functionalized carbon nanotube thin films, prepared using the vacuum filtration method, were decorated with Au nanoparticles by in situ reduction of HAuCl4 under mild conditions. These Au nanoparticles were subsequently employed
for the growth of GaAs nanowires (NWs) by the vapor-liquid-solid process in a gas source molecular beam epitaxy system. The process resulted in the dense growth of GaAs NWs across the entire surface of the single-walled nanotube (SWNT) films. The NWs, which were orientated in a variety of angles with respect to the SWNT films, ranged in diameter between 20 to 200 nm, with heights up to 2.5 um. Transmission electron microscopy analysis of the NW-SWNT interface indicated that NW growth was initiated upon the surface of the nanotube composite films. Photoluminescence characterization of a single NW specimen showed high optical quality. Rectifying asymmetric current-voltage behavior was observed from contacted NW ensembles and attributed to the core-shell pn-junction within the NWs. Potential applications of such novel hybrid architectures include flexible solar cells, displays, and sensors.
By sequential feeding of catalyst materials, it is revealed that the active growth sites are at the bottom of the carbon nanotubes (CNTs), and that catalyst particles are constantly encapsulated into nanotubes from the bottom. This gives a better ins
ight into the mechanism of CNT formation and on ways to control the growth process. CNTs encapsulated with different materials should enable the study of their electronic or magnetic properties, with potential applications as building blocks for nanoelectronics and as fillers in composites for electromagenetic shielding.
Pulsed laser deposition from a Nd:YAG laser was employed in production of hundreds of nanometer thick quasicrystalline Ti-Zr-Ni films on glass substrate. The influence of deposition temperature Ts on the structure, morphology and microstructure of th
e films across their thickness was investigated. The morphology and microstructure features were evaluated by X-ray diffraction and transmission electron microscopy techniques. The low deposition temperatures were found to produce films with nanometer sized grains embedded in an amorphous matrix. The grains exhibit quasicrystalline order. The higher deposition temperatures lead to films whose structure is not uniform all along the growth direction. The layer in contact with the substrate is a very thin amorphous layer. The main part of the film consists of crystallized columns. The columns have grown from a nano-crystallized layer where the size of crystallites increases with increasing thickness.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
