اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدPrecipitate stability and recrystallisation in the weld nuggets of friction stir welded Al-Mg-Si and Al-Mg-Sc alloys
115
0
0.0
(
0
)
تأليف
Xavier Sauvage
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Two different precipitate hardening aluminium alloys processed by friction stir welding were investigated. The microstructure and the hardness of the as delivered materials were compared to that of the weld nugget. Transmission electron microscopy observations combined with three-dimensional atom probe analyses clearly show that beta; precipitates dissolved in the nugget of the Al-Mg-Si giving rise to some supersaturated solid solution. It is shown that the dramatic softening of the weld could be partly recovered by post-welding ageing treatments. In the Al-Mg-Sc alloy, Al3Sc precipitate size and density are unchanged in the nugget comparing to the base metal. These precipitates strongly reduce the boundary mobility of recrystallised grains, leading to a grain size in the nugget much smaller than in the Al-Mg-Si alloy. Both coherent and incoherent precipitates were detected. This feature may indicate that a combination of continuous and discontinuous recrystallisation occurred in the weld nugget.
قيم البحث
اقرأ أيضاً
Dislocation velocities and mobilities are studied by Molecular Dynamics simulations for edge and screw dislocations in pure aluminum and nickel, and edge dislocations in Al-2.5%Mg and Al-5.0%Mg random substitutional alloys using EAM potentials. In th
e pure materials, the velocities of all dislocations are close to linear with the ratio of (applied stress)/(temperature) at low velocities, consistent with phonon drag models and quantitative agreement with experiment is obtained for the mobility in Al. At higher velocities, different behavior is observed. The edge dislocation velocity remains dependent solely on (applied stress)/(temperature) up to approximately 1.0 MPa/K, and approaches a plateau velocity that is lower than the smallest forbidden speed predicted by continuum models. In contrast, above a velocity around half of the smallest continuum wave speed, the screw dislocation damping has a contribution dependent solely on stress with a functional form close to that predicted by a radiation damping model of Eshelby. At the highest applied stresses, there are several regimes of nearly constant (transonic or supersonic) velocity separated by velocity gaps in the vicinity of forbidden velocities; various modes of dislocation disintegration and destabilization were also encountered in this regime. In the alloy systems, there is a temperature- and concentration-dependent pinning regime where the velocity drops sharply below the pure metal velocity. Above the pinning regime but at moderate stresses, the velocity is again linear in (applied stress)/(temperature) but with a lower mobility than in the pure metal.
The Mg-Zn and Al-Zn binary alloys have been investigated theoretically under static isotropic pressure. The stable phases of these binaries on both initially hexagonal-close-packed (HCP) and face-centered-cubic (FCC) lattices have been determined by
utilizing an iterative approach that uses a configurational cluster expansion method, Monte Carlo search algorithm, and density functional theory (DFT) calculations. Based on 64-atom models, it is shown that the most stable phases of the Mg-Zn binary alloy under ambient condition are $rm MgZn_3$, $rm Mg_{19}Zn_{45}$, $rm MgZn$, and $rm Mg_{34}Zn_{30}$ for the HCP, and $rm MgZn_3$ and $rm MgZn$ for the FCC lattice, whereas the Al-Zn binary is energetically unfavorable throughout the entire composition range for both the HCP and FCC lattices under all conditions. By applying an isotropic pressure in the HCP lattice, $rm Mg_{19}Zn_{45}$ turns into an unstable phase at P$approx$$10$~GPa, a new stable phase $rm Mg_{3}Zn$ appears at P$gtrsim$$20$~GPa, and $rm Mg_{34}Zn_{30}$ becomes unstable for P$gtrsim$$30$~GPa. For FCC lattice, the $rm Mg_{3}Zn$ phase weakly touches the convex hull at P$gtrsim$$20$~GPa while the other stable phases remain intact up to $approx$$120$~GPa. Furthermore, making use of the obtained DFT results, bulk modulus has been computed for several compositions up to pressure values of the order of $approx$$120$~GPa. The findings suggest that one can switch between $rm Mg$-rich and $rm Zn$-rich early-stage clusters simply by applying external pressure. $rm Zn$-rich alloys and precipitates are more favorable in terms of stiffness and stability against external deformation.
The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23C and 100C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the pre
cipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong hardening. The predictions of the yield stress based on the Orowan model were in reasonable agreement with the experimental data. The presence of rod-shape precipitates perpendicular to the basal plane leads to a strong reduction in the plastic anisotropy of Mg.
Mg grain boundary (GB) segregation and GB diffusion can impact the processing and properties of Al-Mg alloys. Yet, Mg GB diffusion in Al has not been measured experimentally or predicted by simulations. We apply atomistic computer simulations to pred
ict the amount and the free energy of Mg GB segregation, and the impact of segregation on GB diffusion of both alloy components. At low temperatures, Mg atoms segregated to a tilt GB form clusters with highly anisotropic shapes. Mg diffuses in Al GBs slower than Al itself, and both components diffuse slowly in comparison with Al GB self-diffusion. Thus, Mg segregation significantly reduces the rate of mass transport along GBs in Al-Mg alloys. The reduced atomic mobility can be responsible for the improved stability of the microstructure at elevated temperatures.
The effect of Al atoms in solid solution on the critical resolved shear stress for twin nucleation and growth was analyzed by means of the combination of diffusion couples with compression tests in micropillars oriented for twinning. The critical res
olved shear stress for twin nucleation was higher than that for twin growth and both increased by the same amount with the Al content. Nevertheless, the increase was small ( approx. 10 MPa) for 4 at.%Al but large (up to 60-70 MPa) for 9 at.%Al. These results were in agreement with Labusch-models based on first principles calculations in the dilute regime (< 5 at.%Al) [51]. Comparison with recent data in the literature showed that Al atoms are more effective in increasing the critical resolved shear stresses for twin nucleation and growth than for basal slip [21]. Finally, compression tests in micropillars oriented along [0001] showed the critical shear stress for pyramidal slip increased rapidly with the Al content from 98 MPa in pure Mg to 250 MPa in Mg-9 at.%Al. Thus, the addition of Al increased the plastic anisotropy of Mg alloys.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
