اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدGround motion prediction at gravitational wave observatories using archival seismic data
112
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Gravitational wave observatories have always been affected by tele-seismic earthquakes leading to a decrease in duty cycle and coincident observation time. In this analysis, we leverage the power of machine learning algorithms and archival seismic data to predict the ground motion and the state of the gravitational wave interferometer during the event of an earthquake. We demonstrate improvement from a factor of 5 to a factor of 2.5 in scatter of the error in the predicted ground velocity over a previous model fitting based approach. The level of accuracy achieved with this scheme makes it possible to switch control configuration during periods of excessive ground motion thus preventing the interferometer from losing lock. To further assess the accuracy and utility of our approach, we use IRIS seismic network data and obtain similar levels of agreement between the estimates and the measured amplitudes. The performance indicates that such an archival or prediction scheme can be extended beyond the realm of gravitational wave detector sites for hazard-based early warning alerts.
قيم البحث
اقرأ أيضاً
In this paper, we report on the construction of a deep Artificial Neural Network (ANN) to localize simulated gravitational wave signals in the sky with high accuracy. We have modelled the sky as a sphere and have considered cases where the sphere is
divided into 18, 50, 128, 1024, 2048 and 4096 sectors. The sky direction of the gravitational wave source is estimated by classifying the signal into one of these sectors based on its right ascension and declination values for each of these cases. In order to do this, we have injected simulated binary black hole gravitational wave signals of component masses sampled uniformly between 30-80 solar mass into Gaussian noise and used the whitened strain values to obtain the input features for training our ANN. We input features such as the delays in arrival times, phase differences and amplitude ratios at each of the three detectors Hanford, Livingston and Virgo, from the raw time-domain strain values as well as from analytic
With the advent of gravitational wave astronomy, techniques to extend the reach of gravitational wave detectors are desired. In addition to the stellar-mass black hole and neutron star mergers already detected, many more are below the surface of the
noise, available for detection if the noise is reduced enough. Our method (DeepClean) applies machine learning algorithms to gravitational wave detector data and data from on-site sensors monitoring the instrument to reduce the noise in the time-series due to instrumental artifacts and environmental contamination. This framework is generic enough to subtract linear, non-linear, and non-stationary coupling mechanisms. It may also provide handles in learning about the mechanisms which are not currently understood to be limiting detector sensitivities. The robustness of the noise reduction technique in its ability to efficiently remove noise with no unintended effects on gravitational-wave signals is also addressed through software signal injection and parameter estimation of the recovered signal. It is shown that the optimal SNR ratio of the injected signal is enhanced by $sim 21.6%$ and the recovered parameters are consistent with the injected set. We present the performance of this algorithm on linear and non-linear noise sources and discuss its impact on astrophysical searches by gravitational wave detectors.
Searches for gravitational-wave counterparts have been going in earnest since GW170817 and the discovery of AT2017gfo. Since then, the lack of detection of other optical counterparts connected to binary neutron star or black hole - neutron star candi
dates has highlighted the need for a better discrimination criterion to support this effort. At the moment, the low-latency gravitational-wave alerts contain preliminary information about the binary properties and, hence, on whether a detected binary might have an electromagnetic counterpart. The current alert method is a classifier that estimates the probability that there is a debris disc outside the black hole created during the merger as well as the probability of a signal being a binary neutron star, a black hole - neutron star, a binary black hole or of terrestrial origin. In this work, we expand upon this approach to predict both the ejecta properties and provide contours of potential lightcurves for these events in order to improve follow-up observation strategy. The various sources of uncertainty are discussed, and we conclude that our ignorance about the ejecta composition and the insufficient constraint of the binary parameters, by the low-latency pipelines, represent the main limitations. To validate the method, we test our approach on real events from the second and third Advanced LIGO-Virgo observing runs.
Increasing the laser power is essential to improve the sensitivity of interferometric gravitational wave detectors. However, optomechanical parametric instabilities can set a limit to that power. It is of major importance to understand and characteri
ze the many parameters and effects that influence these instabilities. Here, we model with a high degree of precision the optical and mechanical modes that are involved in these parametric instabilities, such that our model can become predictive. As an example, we perform simulations for the Advanced Virgo interferometer (O3 configuration). In particular we compute mechanical modes losses by combining both on-site measurements and finite element analysis with unprecedented level of detail and accuracy. We also study the influence on optical modes and parametric gains of mirror finite size effects, and mirror deformations due to thermal absorption. We show that these effects play an important role if transverse optical modes of order higher than four are involved in the instability process.
The LIGO observatories detect gravitational waves through monitoring changes in the detectors length down to below $10^{-19}$,$m/sqrt{Hz}$ variation---a small fraction of the size of the atoms that make up the detector. To achieve this sensitivity, t
he detector and its environment need to be closely monitored. Beyond the gravitational wave data stream, LIGO continuously records hundreds of thousands of channels of environmental and instrumental data in order to monitor for possibly minuscule variations that contribute to the detector noise. A particularly challenging issue is the appearance in the gravitational wave signal of brief, loud noise artifacts called ``glitches, which are environmental or instrumental in origin but can mimic true gravitational waves and therefore hinder sensitivity. Currently they are primarily identified by analysis of the gravitational wave data stream. Here we present a machine learning approach that can identify glitches by monitoring textit{all} environmental and detector data channels, a task that has not previously been pursued due to its scale and the number of degrees of freedom within gravitational-wave detectors. The presented method is capable of reducing the gravitational-wave detector networks false alarm rate and improving the LIGO instruments, consequently enhancing detection confidence.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
