اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدExperimental and numerical determination of mechanical properties of polygonal wood particles and their flow analysis in silos
308
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Responding to a lack in the literature, mechanical properties of polygonal wood particles are determined for use in a discrete element model (DEM) for flow analysis in silos, and some methods are proposed for determining such parameters. The parameters arrived at here have also formed part of the input to the SPOLY software, developed in-house to compute the DEM model with spheropolyhedron elements. The model is validated using a 2D physical model, where prismatic particles with polygonal cross sections are placed inside a silo with variable aperture and hopper angle. Validation includes comparison of flow-rates computed by SPOLY, displacement profiles, and clogging thresholds with experimental results. The good agreement that emerges will encourage future use of miniature triaxial tests, grain-surface profilometry, inclined slope tests, and numerical analysis of the intragranular stresses - toward a direct construction of the contact-deformation relations required in realistic DEM modelling of particle flow with angular-shaped particles.
قيم البحث
اقرأ أيضاً
The dynamics of inertial particles in Rayleigh-B{e}nard convection, where both particles and fluid exhibit thermal expansion, is studied using direct numerical simulations (DNS). We consider the effect of particles with a thermal expansion coefficien
t larger than that of the fluid, causing particles to become lighter than the fluid near the hot bottom plate and heavier than the fluid near the cold top plate. Because of the opposite directions of the net Archimedes force on particles and fluid, particles deposited at the plate now experience a relative force towards the bulk. The characteristic time for this motion towards the bulk to happen, quantified as the time particles spend inside the thermal boundary layers (BLs) at the plates, is shown to depend on the thermal response time, $tau_T$, and the thermal expansion coefficient of particles relative to that of the fluid, $K = alpha_p / alpha_f$. In particular, the residence time is constant for small thermal response times, $tau_T lesssim 1$, and increasing with $tau_T$ for larger thermal response times, $tau_T gtrsim 1$. Also, the thermal BL residence time is increasing with decreasing $K$. A one-dimensional (1D) model is developed, where particles experience thermal inertia and their motion is purely dependent on the buoyancy force. Although the values do not match one-to-one, this highly simplified 1D model does predict a regime of a constant thermal BL residence time for smaller thermal response times and a regime of increasing residence time with $tau_T$ for larger response times, thus explaining the trends in the DNS data well.
Two identical particles driven by the same steady force through a viscous fluid may move relative to one another due to hydrodynamic interactions. The presence or absence of this relative translation has a profound effect on the dynamics of a driven
suspension consisting of many particles. We consider a pair of particles which, to linear order in the force, do not interact hydrodynamically. If the system possesses an intrinsic property (such as the shape of the particles, their position with respect to a boundary, or the shape of the boundary) which is affected by the external forcing, hydrodynamic interactions that depend nonlinearly on the force may emerge. We study the general properties of such nonlinear response. Analysis of the symmetries under particle exchange and under force reversal leads to general conclusions concerning the appearance of relative translation and the motions time-reversibility. We demonstrate the applicability of the conclusions in three specific examples: (a) two spheres driven parallel to a wall; (b) two deformable objects driven parallel to their connecting line; and (c) two spheres driven along a curved path. The breaking of time-reversibility suggests a possible use of nonlinear hydrodynamic interactions to disperse or assemble particles by an alternating force.
Dynamics of regular clusters of many non-touching particles falling under gravity in a viscous fluid at low Reynolds number are analysed within the point-particle model. Evolution of two families of particle configurations is determined: 2 or 4 regul
ar horizontal polygons (called `rings) centred above or below each other. Two rings fall together and periodically oscillate. Four rings usually separate from each other with chaotic scattering. For hundreds of thousands of initial configurations, a map of the cluster lifetime is evaluated, where the long-lasting clusters are centred around periodic solutions for the relative motions, and surrounded by regions of the chaotic scattering,in a similar way as it was observed by Janosi et al. (1997) for three particles only. These findings suggest to consider the existence of periodic orbits as a possible physical mechanism of the existence of unstable clusters of particles falling under gravity in a viscous fluid.
As 2D materials such as graphene, transition metal dichalcogenides, and 2D polymers become more prevalent, solution processing and colloidal-state properties are being exploited to create advanced and functional materials. However, our understanding
of the fundamental behavior of 2D sheets and membranes in fluid flow is still lacking. In this work, we perform numerical simulations of athermal semiflexible sheets with hydrodynamic interactions in shear flow. For sheets initially oriented in the flow-gradient plane, we find buckling instabilities of different mode numbers that vary with bending stiffness and can be understood with a quasi-static model of elasticity. For different initial orientations, chaotic tumbling trajectories are observed. Notably, we find that sheets fold or crumple before tumbling but do not stretch again upon applying greater shear.
Many textbooks dealing with surface tension favor the thermodynamic approach (minimization of some thermodynamic potential such as free energy) over the mechanical approach (balance of forces) to describe capillary phenomena, stating that the latter
is flawed and misleading. Yet, mechanical approach is more intuitive for students than free energy minimization, and does not require any knowledge of thermodynamics. In this paper we show that capillary phenomena can be unmistakably described using the mechanical approach, as long as the system on which the forces act is properly defined. After reminding the microscopic origin of a tangential tensile force at the interface, we derive the Young-Dupr{e} equation, emphasizing that this relation should be interpreted as an interface condition at the contact line, rather than a force balance equation. This correct interpretation avoids misidentification of capillary forces acting on a given system. Moreover, we show that a reliable method to correctly identify the acting forces is to define a control volume that does not embed any contact line on its surface. Finally, as an illustration of this method, we apply the mechanical approach in a variety of ways on a classic example: the derivation of the equilibrium height of capillary rise (Jurins law).
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
