اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدMetacomposite characteristics and their influential factors of polymer composites containing orthogonal ferromagnetic microwire arrays
571
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The microwave properties of glass-fibers reinforced polymer composite embedded with an orthogonal array of Fe77Si10B10C3 microwires have been investigated. The composites containing orthogonal wire arrays display a remarkable transmission window in the frequency band of 1 to 6 GHz under zero external magnetic field indicating an intrinsic double-negative-index characteristic. The polymer matrices have proved to exert a synergistic effect on the microwave properties, which is responsible for the disappearance of the transmission windows when Ek is perpendicular to the glass fiber direction. The plasma frequency of the orthogonal microwire array composite is higher than that of the parallel microwire array with identical wire spacing; this could be attributed to the enhanced microwire-wave interaction induced by the axial electrical components on the additional layer of perpendicular wires. All these features make this new kind of orthogonal microwire composites promising for potential cloaking and sensing applications.
قيم البحث
اقرأ أيضاً
Traditional approaches to realize microwave tunability in microwire polymer composites which mainly rely on topological factors, magnetic field/stress stimuli, and hybridization prove to be burdensome and restricted to rather narrow band frequencies.
This work presents a novel yet facile strategy based on a single component tunable medium to program the transmission response over wide frequency bands. To this end, we demonstrated that structural modification of one type of microwire through suitable current annealing and arrangement of the annealed wires in multiple combinations were sufficient to distinctly red-shift the transmission dip frequency of the composites. Such one wire control-strategy endorsed a programmable multivariable system grounded on the variations in both the overall array conductivity or effectiv area determined by the wires arrangement and the relaxation time dictated by the annealing degree of microwires. These results can be used to prescribe transmission frequency bands of desired features via diverse microwire arrays and microwave performance from a single component to a composite system design.
We have investigated the microwave properties of epoxy-based composites containing melt-extracted Co69.25Fe4. 25B13.5-xSi13Nbx (x=0, 1, 3) microwires of various length annealed using a so-called combined current-modulation annealing (CCMA) technique.
The observation of a double-peak feature in the permittivity spectra is believed due to the coexistence of the amorphous phase and a small amount of nanocrystallites on the wires with a high Nb content. CCMA was found to be favorable for a better-defined circular anisotropy of microwires and had suppressed the highfrequency peak due to residual stress relief for the composite with 25 mm long wires. Neither the shift of resonance peak nor the characteristic double peak feature was detected for composites containing as-cast 15 or 35 mm long microwires.
The observation of strong magnetoelectric effects is reported in thick film bilayers and multilayers of ferrite-lead titanate zirconate (PZT) and lanthanum nanganite-PZT. The ferrites used in our studies included pure and zinc substituted cobalt-, ni
ckel- and lithium ferrites. Samples were prepared by sintering 10-40 mm thick films obtained by tape-casting. Measurements of ME voltage coefficients at 10-1000 Hz indicated a giant ME effect in nickel ferrite-PZT, but a relatively weak coupling in other ferrite-PZT and manganite-PZT systems. Multilayers prepared by hot pressing was found to show a higher ME coefficient than sintered samples. Evidence was found for enhancement in ME coefficients when Zn was substituted in ferrites. The Zn-assisted increase was attributed to low anisotropy and high permeability that resulted in favorable magneto-mechanical coupling in the composites. We analyzed the data in terms of our recent comprehensive theory that takes into account actual interface conditions by introducing an interface coupling parameter. Theoretical longitudinal and transverse ME voltage coefficients for unclamped and clamped samples are in general agreement with data. From the analysis we inferred excellent interface coupling for nickel zinc ferrite-PZT and weak coupling for other layered systems.
We report the results of an experimental study of thermal and magnetic properties of nanostructured ferrimagnetic iron oxide composites with graphene and graphite fillers synthesized via the current activated pressure assisted densification. The ther
mal conductivity was measured using the laser-flash and transient plane source techniques. It was demonstrated that addition of 5 wt. % of equal mixture of graphene and graphite flakes to the composite results in a factor of x2.6 enhancement of the thermal conductivity without significant degradation of the saturation magnetization. The microscopy and spectroscopic characterization reveal that sp2 carbon fillers preserve their crystal structure and morphology during the composite processing. The strong increase in the thermal conductivity was attributed to the excellent phonon heat conduction properties of graphene and graphite. The results are important for energy and electronic applications of the nanostructured permanent magnets.
To determine the friction coefficient of graphene, micro-scale scratch tests are conducted on exfoliated and epitaxial graphene at ambient conditions. The experimental results show that the monolayer, bilayer, and trilayer graphene all yield friction
coefficients of approximately 0.03. The friction coefficient of pristine graphene is less than that of disordered graphene, which is treated by oxygen plasma. Ramping force scratch tests are performed on graphene with various numbers of layers to determine the normal load required for the probe to penetrate graphene. A very low friction coefficient and also its high pressure resistance make graphene a promising material for antiwear coatings.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
