اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدControlling the electronic structure of graphene using surface-adsorbate interactions
126
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We show that strong coupling between graphene and the substrate is mitigated when 0.8 monolayer of Na is adsorbed and consolidated on top graphene-on-Ni(111). Specifically, the {pi} state is partially restored near the K-point and the energy gap between the {pi} and {pi}* states reduced to 1.3 eV after adsorption, as measured by angle-resolved photoemission spectroscopy. We show that this change is not caused by intercalation of Na to underneath graphene but it is caused by an electronic coupling between Na on top and graphene. We show further that graphene can be decoupled to a much higher extent when Na is intercalated to underneath graphene. After intercalation, the energy gap between the {pi} and {pi}* states is reduced to 0 eV and these states are identical as in freestanding and n-doped graphene. We conclude thus that two mechanisms of decoupling exist: a strong decoupling through intercalation, which is the same as one found using noble metals, and a weak decoupling caused by electronic interaction with the adsorbate on top.
قيم البحث
اقرأ أيضاً
We propose a mechanism to control the interaction between adsorbates on graphene. The interaction between a pair of adsorbates---the change in adsorption energy of one adsorbate in the presence of another---is dominated by the interaction mediated by
graphenes pi-electrons and has two distinct regimes. Ab initio density functional, numerical tight-binding, and analytical calculations are used to develop the theory. We demonstrate that the interaction can be tuned in a wide range by adjusting the adsorbate-graphene bonding or the chemical potential.
We study the electronic structure of graphene in the presence of either sevenfolds or eightfolds by using a gauge field-theory model. The graphene sheet with topological defects is considered as a negative cone surface with infinite Gaussian curvatur
e at the center. The density of electronic states is calculated for a single seven- and eightfold as well as for a pair of sevenfolds with different morphology. The density of states at the Fermi energy is found to be zero in all cases except two sevenfolds with translational factor $M eq 0$.
We formulate the theory of the perturbation caused by an adsorbate upon the substrate lattice in terms of a local modification of the interatomic potential energy around the adsorption site, which leads to the relaxation of substrate atoms. We apply
the approach to CO chemisorption on close-packed metal surfaces, and show that the adsorbate-adsorbate interaction and a variety of other properties can be well described by a simple model.
The idea that surface effects may play an important role in suppressing $e_g$ Fermi surface pockets on Na$_x$CoO$_2$ $(0.333 le x le 0.75)$ has been frequently proposed to explain the discrepancy between LDA calculations (performed on the bulk compou
nd) which find $e_g$ hole pockets present and ARPES experiments, which do not observe the hole pockets. Since ARPES is a surface sensitive technique it is important to investigate the effects that surface formation will have on the electronic structure of Na$_{1/3}$CoO$_2$ in order to more accurately compare theory and experiment. We have calculated the band structure and Fermi surface of cleaved Na$_{1/3}$CoO$_2$ and determined that the surface non-trivially affects the fermiology in comparison to the bulk. Additionally, we examine the likelihood of possible hydroxyl cotamination and surface termination. Our results show that a combination of surface formation and contamination effects could resolve the ongoing controversy between ARPES experiments and theory.
Tuning the work functions of materials is of practical interest for maximizing the performance of microelectronic and (photo)electrochemical devices, as the efficiency of these systems depends on the ability to control electronic levels at surfaces a
nd across interfaces. Perovskites are promising compounds to achieve such control. In this work, we examine the work functions of more than 1,000 perovskite oxide surfaces (ABO$_3$) by data-driven (machine-learning) analysis and identify the factors that determine their magnitude. While the work functions of BO$_2$-terminated surfaces are sensitive to the energy of the hybridized oxygen p bands, the work functions of AO-terminated surfaces exhibit a much less trivial dependence with respect to the filling of the d bands of the B-site atom and of its electronic affinity. This study shows the utility of interpretable data-driven models in analyzing the work functions of cubic perovskites from a limited number of electronic-structure descriptors.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
