اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدA new technique for timing the double pulsar system
435
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In 2004, McLaughlin et al. discovered a phenomenon in the radio emission of PSR J0737-3039B (B) that resembles drifting sub-pulses. The repeat rate of the sub-pulses is equal to the spin frequency of PSR J0737-3039A (A); this led to the suggestion that they are caused by incidence upon Bs magnetosphere of electromagnetic radiation from A. Here we describe a geometrical model which predicts the delay of Bs sub-pulses relative to As radio pulses. We show that measuring these delays is equivalent to tracking As rotation from the point of view of an hypothetical observer located near B. This has three main astrophysical applications: (a) to determine the sense of rotation of A relative to its orbital plane; (b) to estimate where in Bs magnetosphere the radio sub-pulses are modulated and (c) to provide an independent estimate of the mass ratio of A and B. The latter might improve existing tests of gravitational theories using this system.
قيم البحث
اقرأ أيضاً
The PSRIX backend is the primary pulsar timing instrument of the Effelsberg 100-m radio telescope since early 2011. This new ROACH-based system enables bandwidths up to 500 MHz to be recorded, significantly more than what was possible with its predec
essor, the Effelsberg-Berkeley Pulsar Processor (EBPP). We review the first four years of PSRIX timing data for 33 pulsars collected as part of the monthly European Pulsar Timing Array (EPTA) observations. We describe the automated data analysis pipeline, CoastGuard, that we developed to reduce these observations. We also introduce TOASTER, the EPTA timing database used to store timing results, processing information and observation metadata. Using these new tools, we measure the phase-averaged flux densities at 1.4 GHz of all 33 pulsars. For 7 of these pulsars, our flux density measurements are the first values ever reported. For the other 26 pulsars, we compare our flux density measurements with previously published values. By comparing PSRIX data with EBPP data, we find an improvement of ~2-5 times in signal-to-noise ratio achievable, which translates to an increase of ~2-5 times in pulse time-of-arrival (TOA) precision. We show that such an improvement in TOA precision will improve the sensitivity to the stochastic gravitational wave background. Finally, we showcase the flexibility of the new PSRIX backend by observing several millisecond-period pulsars (MSPs) at 5 and 9 GHz. Motivated by our detections, we discuss the potential for complementing existing pulsar timing array data sets with MSP monitoring campaigns at these frequencies.
We have constructed a new timescale, TT(IPTA16), based on observations of radio pulsars presented in the first data release from the International Pulsar Timing Array (IPTA). We used two analysis techniques with independent estimates of the noise mod
els for the pulsar observations and different algorithms for obtaining the pulsar timescale. The two analyses agree within the estimated uncertainties and both agree with TT(BIPM17), a post-corrected timescale produced by the Bureau International des Poids et Mesures (BIPM). We show that both methods could detect significant errors in TT(BIPM17) if they were present. We estimate the stability of the atomic clocks from which TT(BIPM17) is derived using observations of four rubidium fountain clocks at the US Naval Observatory. Comparing the power spectrum of TT(IPTA16) with that of these fountain clocks suggests that pulsar-based timescales are unlikely to contribute to the stability of the best timescales over the next decade, but they will remain a valuable independent check on atomic timescales. We also find that the stability of the pulsar-based timescale is likely to be limited by our knowledge of solar-system dynamics, and that errors in TT(BIPM17) will not be a limiting factor for the primary goal of the IPTA, which is to search for the signatures of nano-Hertz gravitational waves.
In-spiraling supermassive black holes should emit gravitational waves, which would produce characteristic distortions in the time of arrival residuals from millisecond pulsars. Multiple national and regional consortia have constructed pulsar timing a
rrays by precise timing of different sets of millisecond pulsars. An essential aspect of precision timing is the transfer of the times of arrival to a (quasi-)inertial frame, conventionally the solar system barycenter. The barycenter is determined from the knowledge of the planetary masses and orbits, which has been refined over the past 50 years by multiple spacecraft. Within the North American Nanohertz Observatory for Gravitational Waves (NANOGrav), uncertainties on the solar system barycenter are emerging as an important element of the NANOGrav noise budget. We describe what is known about the solar system barycenter, touch upon how uncertainties in it affect gravitational wave studies with pulsar timing arrays, and consider future trends in spacecraft navigation.
Over the past few decades, the measurement precision of some pulsar-timing experiments has advanced from ~10 us to ~10 ns, revealing many subtle phenomena. Such high precision demands both careful data handling and sophisticated timing models to avoi
d systematic error. To achieve these goals, we present PINT (PINT Is Not Tempo3), a high-precision Python pulsar timing data analysis package, which is hosted on GitHub and available on Python Package Index (PyPI) as pint-pulsar. PINT is well-tested, validated, object-oriented, and modular, enabling interactive data analysis and providing an extensible and flexible development platform for timing applications. It utilizes well-debugged public Python packages (e.g., the NumPy and Astropy libraries) and modern software development schemes (e.g., version control and efficient development with git and GitHub) and a continually expanding test suite for improved reliability, accuracy, and reproducibility. PINT is developed and implemented without referring to, copying, or transcribing the code from other traditional pulsar timing software packages (e.g., TEMPO and TEMPO2) and therefore provides a robust tool for cross-checking timing analyses and simulating pulse arrival times. In this paper, we describe the design, usage, and validation of PINT, and we compare timing results between it and TEMPO and TEMPO2.
We describe the procedure, nuances, issues, and choices involved in creating times-of-arrival (TOAs), residuals and error bars from a set of radio pulsar timing data. We discuss the issue of mis-matched templates, the problem that wide- bandwidth bac
kends introduce, possible solutions to that problem, and correcting for offsets introduced by various observing systems.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
