اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدNumerical Simulation of Particle Flow in a Sand Trap
170
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Sand traps are used to measure Aeolian flux. Since they modify the surrounding wind velocity field their gauging represents an important challenge. We use numerical simulations under the assumption of homogeneous turbulence based on FLUENT to systematically study the flow field and trapping efficiency of one of the most common devices based on a hollow cylinder with two slits. In particular, we investigate the dependence on the wind speed, the Stokes number, the permeability of the membrane on the slit and the saltation height.
قيم البحث
اقرأ أيضاً
A direct numerical simulation (DNS) of a channel flow with one curved surface was performed at moderate Reynolds number (Re_tau = 395 at the inlet). The adverse pressure gradient was obtained by a wall curvature through a mathematical mapping from ph
ysical coordinates to Cartesian ones. The code, using spectral spanwise and normal discretization, combines the advantage of a good accuracy with a fast integration procedure compared to standard numerical procedures for complex geometries. The turbulent flow slightly separates on the profile at the lower curved wall and is at the onset of separation at the opposite flat wall. The thin separation bubble is characterized with a reversal flow fraction. Intense vortices are generated near the separation line on the lower wall but also at the upper wall. Turbulent normal stresses and kinetic energy budget are investigated along the channel.
Most fluid flow problems that are vital in engineering applications involve at least one of the following features: turbulence, shocks, and/or material interfaces. While seemingly different phenomena, these flows all share continuous generation of hi
gh wavenumber modes, which we term the $k_infty$ irregularity. In this work, an inviscid regularization technique called observable regularization is proposed for the simulation of two-phase compressible flows. The proposed approach regularizes the equations at the level of the partial differential equation and as a result, any numerical method can be used to solve the system of equations. The regularization is accomplished by introducing an observability limit that represents the length scale below which one cannot properly model or continue to resolve flow structures. An observable volume fraction equation is derived for capturing the material interface, which satisfies the pressure equilibrium at the interface. The efficacy of the observable regularization method is demonstrated using several test cases, including a one-dimensional material interface tracking, one-dimensional shock-tube and shock-bubble problems, and two-dimensional simulations of a shock interacting with a cylindrical bubble. The results show favorable agreement, both qualitatively and quantitatively, with available exact solutions or numerical and experimental data from the literature. The computational saving by using the current method is estimated to be about one order of magnitude in two-dimensional computations and significantly higher in three-dimensional computations. Lastly, the effect of the observability limit and best practices to choose its value are discussed.
Cardiovascular diseases, specifically cerebral aneurysms, represent a major cause of morbidity and mortality, having a significant impact on the cost and overall status of health care. In the present work, we employ a haemorheological blood model ori
ginally proposed by Owens to investigate the haemodynamics of blood flow through an aneurytic channel. This constitutive equation for whole human blood is derived using ideas drawn from temporary polymer network theory to model the aggregation and disaggregation of erythrocytes in normal human blood at different shear rates. To better understand the effect of rheological models on the haemodynamics of blood flow in cerebral aneurysms we compare our numerical results with those obtained with other rheological models such as the Carreau-Yasuda (C-Y) model. The results show that the velocity profiles for the Newtonian and the Owens models are approximately similar but differ from those of the C-Y model. In order to stabilize our numerical simulations, we propose two new stabilization techniques, the so-called N-Owens and I-Owens methods. Employing the N-Owens stabilization method enables us to capture the effect of erythrocyte aggregation in blood flow through a cerebral aneurysm at higher Weissenberg (We) and Reynolds (Re) numbers than would otherwise be possible.
This work presents a new multiphase SPH model that includes the shifting algorithm and a variable smoothing length formalism to simulate multi-phase flows with accuracy and proper interphase management. The implementation was performed in the DualSPH
ysics code and validated for different canonical experiments, such as the single-phase and multiphase Poiseuille and Couette test cases. The method is accurate even for the multiphase case for which two phases are simulated. The shifting algorithm and the variable smoothing length formalism has been applied in the multiphase SPH model to improve the numerical results at the interphase even when it is highly deformed and non-linear effects become important. The obtained accuracy in the validation tests and the good interphase definition in the instability cases indicate an important improvement in the numerical results compared with single-phase and multiphase models where the shifting algorithm and the variable smoothing length formalism are not applied.
Rod bundle flows are commonplace in nuclear engineering, and are present in light water reactors (LWRs) as well as other more advanced concepts. Inhomogeneities in the bundle cross section can lead to complex flow phenomena, including varying local c
onditions of turbulence. Despite the decades of numerical and experimental investigations regarding this topic, and the importance of elucidating the physics of the flow field, to date there are few publicly available direct numerical simulations (DNS) of the flow in multiple-pin rod bundles. Thus a multiple-pin DNS study can provide significant value toward reaching a deeper understanding of the flow physics, as well as a reference simulation for development of various reduced-resolution analysis techniques. To this end, DNS of the flow in a square 5x5 rod bundle at Reynolds number of 19,000 has been performed using the highly-parallel spectral element code Nek5000. The geometrical dimensions were representative of typical LWR fuel designs. The DNS was designed using microscales estimated from an advanced Reynolds-Averaged Navier-Stokes (RANS) model. Characteristics of the velocity field, Reynolds stresses, and anisotropy are presented in detail for various regions of the bundle. The turbulent kinetic energy budget is also presented and discussed
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
