اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدOptimal Light Beams and Mirror Shapes for Future LIGO Interferometers
119
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report the results of a recent search for the lowest value of thermal noise that can be achieved in LIGO by changing the shape of mirrors, while fixing the mirror radius and maintaining a low diffractional loss. The result of this minimization is a beam with thermal noise a factor of 2.32 (in power) lower than previously considered Mesa Beams and a factor of 5.45 (in power) lower than the Gaussian beams employed in the current baseline design. Mirrors that confine these beams have been found to be roughly conical in shape, with an average slope approximately equal to the mirror radius divided by arm length, and with mild corrections varying at the Fresnel scale. Such a mirror system, if built, would impact the sensitivity of LIGO, increasing the event rate of observing gravitational waves in the frequency range of maximum sensitivity roughly by a factor of three compared to an Advanced LIGO using Mesa beams (assuming all other noises remain unchanged). We discuss the resulting beam and mirror properties and study requirements on mirror tilt, displacement and figure error, in order for this beam to be used in LIGO detectors.
قيم البحث
اقرأ أيضاً
The first generation of ground-based interferometric gravitational wave detectors, LIGO, GEO and Virgo, have operated and taken data at their design sensitivities over the last few years. The data has been examined for the presence of gravitational w
ave signals. Presented here is a comprehensive review of the most significant results. The network of detectors is currently being upgraded and extended, providing a large likelihood for observations. These future prospects will also be discussed.
We have developed, produced and characterised integrated sensors, actuators and the related read-out and drive electronics that will be used for the control of the Advanced LIGO suspensions. The overall system consists of the BOSEMs (displacement sen
sor with integrated electro-magnetic actuator), the satellite boxes (BOSEM readout and interface electronics) and six different types of coil-driver units. In this paper we present the design of this read-out and control system, we discuss the related performance relevant for the Advanced LIGO suspensions, and we report on the experimental activity finalised at the production of the instruments for the Advanced LIGO detectors.
We consider a class of proposed gravitational wave detectors based on multiple atomic interferometers separated by large baselines and referenced by common laser systems. We compute the sensitivity limits of these detectors due to intrinsic phase noi
se of the light sources, non-inertial motion of the light sources, and atomic shot noise and compare them to sensitivity limits for traditional light interferometers. We find that atom interferometers and light interferometers are limited in a nearly identical way by intrinsic phase noise and that both require similar mitigation strategies (e.g. multiple arm instruments) to reach interesting sensitivities. The sensitivity limit from motion of the light sources is slightly different and favors the atom interferometers in the low-frequency limit, although the limit in both cases is severe.
We describe three fundamentally different methods we have applied to calibrate the test mass displacement actuators to search for systematic errors in the calibration of the LIGO gravitational-wave detectors. The actuation frequencies tested range fr
om 90 Hz to 1 kHz and the actuation amplitudes range from 1e-6 m to 1e-18 m. For each of the four test mass actuators measured, the weighted mean coefficient over all frequencies for each technique deviates from the average actuation coefficient for all three techniques by less than 4%. This result indicates that systematic errors in the calibration of the responses of the LIGO detectors to differential length variations are within the stated uncertainties.
The relic gravitational wave (RGW) generated during the inflation depends on the initial condition via the amplitude, the spectral index $n_t$ and the running index $alpha_t$. CMB observations so far have only constrained the tensor-scalar ratio $r$,
but not $n_t$ nor $alpha_t$. Complementary to this, the ground-based interferometric detectors working at $sim 10^2$Hz are able to constrain the spectral indices that influence the spectrum sensitively at high frequencies. In this work we give a proper normalization of the analytical spectrum at the low frequency end, yielding a modification by a factor of $sim 1/50$ to the previous treatment. We calculate the signal-noise ratios (SNR) for various ($n_t,alpha_t$) at fixed $r=0.2$ by S6 of LIGO H-L, and obtain the observational upper limit on the running index $alpha_t<0.02093$ (i.e, at a detection rate $95%$ and a false alarm rate $5%$) at the default $(n_t=0,r=0.2)$. This is consistent with the constraint on the energy density obtained by LIGO-Virgo Collaboration. Extending to the four correlated detectors currently running, the calculated SNR improves slightly. When extending to the six correlated detectors of the second-generation in design, the calculated SNR is $sim 10^3$ times over the previous two cases, due to the high sensitivities. RGW can be directly detected by the six 2nd-generation detectors for models with $alpha_t>0.01364$.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
