اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدProduction Performance of the ATLAS Semiconductor Tracker Readout System
89
0
0.0
(
0
)
تأليف
Vasiliki A. Mitsou
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The ATLAS Semiconductor Tracker (SCT) together with the pixel and the transition radiation detectors will form the tracking system of the ATLAS experiment at LHC. It will consist of 20000 single-sided silicon microstrip sensors assembled back-to-back into modules mounted on four concentric barrels and two end-cap detectors formed by nine disks each. The SCT module production and testing has finished while the macro-assembly is well under way. After an overview of the layout and the operating environment of the SCT, a description of the readout electronics design and operation requirements will be given. The quality control procedure and the DAQ software for assuring the electrical functionality of hybrids and modules will be discussed. The focus will be on the electrical performance results obtained during the assembly and testing of the end-cap SCT modules.
قيم البحث
اقرأ أيضاً
The SemiConductor Tracker (SCT) together with the Pixel detector and the Transition Radiation Tracker (TRT) form the central tracking system of the ATLAS experiment at the LHC. It consists of single-sided microstrip silicon sensors, which are read ou
t via binary ASICs based on the DMILL technology, and the data are transmitted via radiation-hard optical fibres. After an overview of the SCT detector layout and readout system, the final-stage assembly of large-scale structures and the integration with the TRT is presented. The focus is on the electrical performance of the overall SCT detector system through the different integration stages, including the detector control and data acquisition system.
This paper presents the design and simulation results of a gigabit transceiver Application Specific Integrated Circuit (ASIC) called GBCR for the ATLAS Inner Tracker (ITk) Pixel detector readout upgrade. GBCR has four upstream receiver channels and a
downstream transmitter channel. Each upstream channel operates at 5.12 Gbps, while the downstream channel operates at 2.56 Gbps. In each upstream channel, GBCR equalizes a signal received through a 5-meter 34-American Wire Gauge (AWG) twin-axial cable, retimes the data with a recovered clock, and drives an optical transmitter. In the downstream channel, GBCR receives the data from an optical receiver and drives the same type of cable as the upstream channels. The output jitter of an upstream channel is 26.5 ps and the jitter of the downstream channel after the cable is 33.5 ps. Each upstream channel consumes 78 mW and each downstream channel consumes 27 mW. Simulation results of the upstream test channel suggest that a significant jitter reduction could be achieved with minimally increased power consumption by using a Feed Forward Equalizer (FFE) + Decision Feedback Equalization (DFE) in addition to the linear equalization of the baseline channel. GBCR is designed in a 65-nm CMOS technology.
We present a gigabit transceiver prototype Application Specific Integrated Circuit (ASIC), GBCR, for the ATLAS Inner Tracker (ITk) Pixel detector readout upgrade. GBCR is designed in a 65-nm CMOS technology and consists of four upstream receiver chan
nels, a downstream transmitter channel, and an Inter-Integrated Circuit (I2C) slave. The upstream channels receive the data at 5.12 Gbps passing through 5-meter 34-American Wire Gauge (AWG) Twin-axial (Twinax) cables, equalize them, retime them with a recovered clock, and then drive an optical transmitter. The downstream channel receives the data at 2.56 Gbps from an optical receiver and drives the cable as same as the upstream channels. The jitter of the upstream channel output is measured to be 35 ps (peak-peak) when the Clock-Data Recovery (CDR) module is turned on and the jitter of the downstream channel output after the cable is 138 ps (peak-peak). The power consumption of each upstream channel is 72 mW when the CDR module is turned on and the downstream channel consumes 27 mW. GBCR survives the total ionizing dose of 200 kGy.
The ATLAS trigger has been used very successfully to collect collision data during 2009 and 2010 LHC running at centre of mass energies of 900 GeV, 2.36 TeV, and 7 TeV. This paper presents the ongoing work to commission the ATLAS trigger with proton
collisions, including an overview of the performance of the trigger based on extensive online running. We describe how the trigger has evolved with increasing LHC luminosity and give a brief overview of plans for forthcoming LHC running.
The Belle II experiment at the SuperKEKB collider at KEK, Tsukuba, Japan has successfully started taking data with the full detector in March 2019. Belle II is a luminosity frontier experiment of the new generation to search for physics beyond the St
andard Model of elementary particles, from precision measurements of a huge number of B and charm mesons and tau leptons. In order to read out the events at a high rate from the seven subdetectors of Belle II, we adopt a highly unified readout system, including a unified trigger timing distribution system (TTD), a unified high speed data link system (Belle2link), and a common backend system to receive Belle2link data. Each subdetector frontend readout system has a field-programmable gate array (FPGA) in which unified firmware components of the TTD receiver and Belle2link transmitter are embedded. The system is designed for data taking at a trigger rate up to 30 kHz with a dead-time fraction of about 1% in the frontend readout system. The trigger rate is still much lower than our design. However, the background level is already high due to the initial vacuum condition and other accelerator parameters, and it is the most limiting factor of the accelerator and detector operation. Hence the occupancy and radiation effects to the frontend electronics are rather severe, and they cause various kind of instabilities. We present the performance of the system, including the achieved trigger rate, dead-time fraction, stability, and discuss the experience gained during the operation.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
