اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe Trigger System of the ARGO-YBJ detector
181
0
0.0
(
0
)
تأليف
S. Mastroianni
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The ARGO-YBJ experiment has been designed to detect air shower events over a large size scale and with an energy threshold of a few hundreds GeV. The building blocks of the ARGO-YBJ detector are single-gap Resistive Plate Counters (RPCs). The trigger logic selects the events on the basis of their hit multiplicity. Inclusive triggers as well as dedicated triggers for specific physics channels or calibration purposes have been developed. This paper describes the architecture and the main features of the trigger system.
قيم البحث
اقرأ أيضاً
The ARGO-YBJ experiment has been designed to study the Extensive Air Showers with an energy threshold lower than that of the existing arrays by exploiting the high altitude location(4300 m a.s.l. in Tibet, P.R. China) and the full ground plane covera
ge. The lower energy limit of the detector (E $sim$ 1 GeV) is reached by the scaler mode technique, i.e. recording the counting rate at fixed time intervals. At these energies, transient signals due to local (e.g. Forbush Decreases) and cosmological (e.g. Gamma Ray Bursts) phenomena are expected as a significant variation of the counting rate compared to the background. In this paper the performance of the ARGO-YBJ detector operating in scaler mode is described and discussed.
The ARGO-YBJ experiment is a full coverage EAS-array installed at the YangBaJing Cosmic Ray Laboratory (4300 m a.s.l., Tibet, P.R. China). We present the results on the angular resolution measured with different methods with the full central carpet.
The comparison of experimental results with MC simulations is discussed.
The ARGO-YBJ experiment consists of a RPC carpet to be operated at the Yangbajing laboratory (Tibet, P.R. China), 4300 m a.s.l., and devoted to the detection of showers initiated by photon primaries in the energy range 100 GeV - 20 TeV. The measureme
nt technique, namely the timing on the shower front with a few tens of particles, requires RPC operation with 1 ns time resolution, low strip multiplicity, high efficiency and low single counting rate. We have tested RPCs with many gas mixtures, at sea level, in order to optimize these parameters. The results of this study are reported.
The ARGO-YBJ experiment, currently under construction at the Yangbaijing Laboratory (4300 m a.s.l.), consists of a single layer of about 2000 Resistive Plate Chambers (RPCs) for a total instrumented area of about 6700 m^2. The digital read-out, perfo
rmed by means of pick-up electrodes 6.7 X 62 cm^2 (strips), allows one to measure the particle number of small size showers. To extend the size range up to the knee region it is necessary to implement the charge read-out of the detector chambers. In order to achieve this goal each RPC has been instrumented with two large size pads of dimensions 140 X 125 cm^2. In this paper the performance of the prototype circuit devoted to the charge read-out is reported.
In any EAS array, the rejection of events with shower cores outside the detector boundaries is of great importance. A large difference between the true and the reconstructed shower core positions may lead to a systematic miscalculation of some shower
characteristics. Moreover, an accurate determination of the shower core position for selected internal events is important to reconstruct the primary direction using conical fits to the shower front, improving the detector angular resolution, or to performe an efficient gamma/hadron discrimination. In this paper we present a procedure able to identify and reject showers with cores outside the ARGO-YBJ carpet boundaries. A comparison of the results for gamma and proton induced showers is reported.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
