اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدA Novel Strategy for GaN-on-Diamond Device with a High Thermal Boundary Conductance
105
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
To achieve high device performance and high reliability for the gallium nitride (GaN)-based high electron mobility transistors (HEMTs), efficient heat dissipation is important but remains challenging. Enormous efforts have been made to transfer a GaN device layer onto a diamond substrate with a high thermal conductivity by bonding. In this work, two GaN-diamond bonded composites are prepared via modified surface activated bonding (SAB) at room temperature with silicon interlayers of different thicknesses (15 nm and 22 nm). Before and after post-annealing process at 800 oC, thermal boundary conductance (TBC) across the bonded interface including the interlayer and the stress of GaN layer are investigated by time-domain thermoreflectance and Raman spectroscopy, respectively. After bonding, the 15 nm Si interlayer achieved a higher TBC. The post-annealing significantly increased the TBC of both interfaces, while the TBC of 22 nm silicon interlayer increased greater and became higher than that of 15 nm. Detailed investigation of the microstructure and composition of the interfaces were carried out to understand the difference in interfacial thermal conduction. The obtained stress was no more than 230 MPa for both before and after the annealing, and this high thermal stability of the bonded composites indicates that the room temperature bonding can realize a GaN-on-diamond template suitable for further epitaxial growth or device process. This work brings a novel strategy of SAB followed by high-temperature annealing to fabricate a GaN-on-diamond device with a high TBC.
قيم البحث
اقرأ أيضاً
The wide bandgap, high-breakdown electric field, and high carrier mobility makes GaN an ideal material for high-power and high-frequency electronics applications such as wireless communication and radar systems. However, the performance and reliabili
ty of GaN-based HEMTs are limited by the high channel temperature induced by Joule-heating in the device channel. High thermal conductivity substrates integrated with GaN can improve the extraction of heat from GaN based HEMTs and lower the device operating temperature. However, heterogeneous integration of GaN with diamond substrates is not trivial and presents technical challenges to maximize the heat dissipation potential brought by the diamond substrate. In this work, two modified room temperature surface activated bonding techniques are used to bond GaN and single crystal diamond with different interlayer thicknesses. TDTR is used to measure the thermal properties from room temperature to 480 K. A relatively large TBC of the GaN-diamond interfaces with a 4nm interlayer was observed and material characterization was performed to link the structure of the interface to the TBC. Device modeling shows that the measured GaN-diamond TBC values obtained from bonding can enable high power GaN devices by taking the full advantage of the high thermal conductivity of single crystal diamond and achieve excellent cooling effect. Furthermore, the room-temperature bonding process in this work do not induce stress problem due to different coefficient of thermal expansion in other high temperature integration processes in previous studies. Our work sheds light on the potential for room-temperature heterogeneous integration of semiconductors with diamond for applications of electronics cooling especially for GaN-on-diamond devices.
GaN-based HEMTs have the potential to be widely used in high-power and high-frequency electronics while their maximum output powers are limited by high channel temperature induced by near-junction Joule-heating, which degrades device performance and
reliability. Increasing the TBC between GaN and SiC will aid in the heat dissipation of GaN-on-SiC power devices, taking advantage of the high thermal conductivity of the SiC substrate. However, a good understanding of the TBC of this technically important interface is still lacking due to the complicated nature of interfacial heat transport. In this work, a lattice-mismatch-insensitive surface activated bonding method is used to bond GaN directly to SiC and thus eliminating the AlN layer altogether. This allows for the direct integration of high quality GaN layers with SiC to create a high thermal boundary conductance interface. TDTR is used to measure the thermal properties of the GaN thermal conductivity and GaN-SiC TBC. The measured GaN thermal conductivity is larger than that of GaN grown by MBE on SiC, showing the impact of reducing the dislocations in the GaN near the interface. High GaN-SiC TBC is observed for the bonded GaN-SiC interfaces, especially for the annealed interface whose TBC (230 MW/m2-K) is close to the highest values ever reported. To understand the structure-thermal property relation, STEM and EELS are used to characterize the interface structure. The results show that, for the as-bonded sample, there exists an amorphous layer near the interface for the as bonded samples. This amorphous layer is crystallized upon annealing, leading to the high TBC found in our work. Our work paves the way for thermal transport across bonded interfaces, which will impact real-world applications of semiconductor integration and packaging.
Several pn junctions were constructed from mechanically exfoliated ultrawide bandgap (UWBG) beta-phase gallium oxide (b{eta}-Ga2O3) and p-type gallium nitride (GaN). The mechanical exfoliation process, which is described in detail, is similar to that
of graphene and other 2D materials. Atomic force microscopy (AFM) scans of the exfoliated b{eta}-Ga2O3 flakes show very smooth surfaces with average roughness of 0.647 nm and transmission electron microscopy (TEM) scans reveal flat, clean interfaces between the b{eta}-Ga2O3 flakes and p-GaN. The device showed a rectification ratio around 541.3 (V+5/V-5). Diode performance improved over the temperature range of 25{deg}C and 200{deg}C, leading to an unintentional donor activation energy of 135 meV. As the thickness of exfoliated b{eta}-Ga2O3 increases, ideality factors decrease as do the diode turn on voltages, tending toward an ideal threshold voltage of 3.2 V as determined by simulation. This investigation can help increase study of novel devices between mechanically exfoliated b{eta}-Ga2O3 and other materials.
Nitrogen-Vacancy centers in diamond possess an electronic spin resonance that strongly depends on temperature, which makes them efficient temperature sensor with a sensitivity down to a few mK/$sqrt{rm Hz}$. However, the high thermal conductivity of
the host diamond may strongly damp any temperature variations, leading to invasive measurements when probing local temperature distributions. In view of determining possible and optimal configurations for diamond-based wide-field thermal imaging, we here investigate, both experimentally and numerically, the effect of the presence of diamond on microscale temperature distributions. Three geometrical configurations are studied: a bulk diamond substrate, a thin diamond layer bonded on quartz and diamond nanoparticles dispersed on quartz. We show that the use of bulk diamond substrates for thermal imaging is highly invasive, in the sense that it prevents any substantial temperature increase. Conversely, thin diamond layers partly solve this issue and could provide a possible alternative for microscale thermal imaging. Dispersions of diamond nanoparticles throughout the sample appear as the most relevant approach as they do not affect the temperature distribution, although NV centers in nanodiamonds yield lower temperature sensitivities compared to bulk diamond.
Devices relying on microwave circuitry form a cornerstone of many classical and emerging quantum technologies. A capability to provide in-situ, noninvasive and direct imaging of the microwave fields above such devices would be a powerful tool for the
ir function and failure analysis. In this work, we build on recent achievements in magnetometry using ensembles of nitrogen vacancy centres in diamond, to present a widefield microwave microscope with few-micron resolution over a millimeter-scale field of view, 130nT/sqrt-Hz microwave amplitude sensitivity, a dynamic range of 48 dB, and sub-ms temporal resolution. We use our microscope to image the microwave field a few microns above a range of microwave circuitry components, and to characterise a novel atom chip design. Our results open the way to high-throughput characterisation and debugging of complex, multi-component microwave devices, including real-time exploration of device operation.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
