اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFrequency Reflection Modulation for Reconfigurable Intelligent Surface Aided OFDM Systems
110
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Reconfigurable intelligent surface (RIS) based reflection modulation has been considered as a promising information delivery mechanism, and has the potential to realize passive information transfer of a RIS without consuming any additional radio frequency chain and time/frequency/energy resources. The existing on-off reflection modulation (ORM) schemes are based on manipulating the ``on/off states of RIS elements, which may lead to the degradation of RIS reflection efficiency. This paper proposes a frequency reflection modulation (FRM) method for RIS-aided OFDM systems. The FRM-OFDM scheme modulates the frequency of the incident electromagnetic waves, and the RIS information is embedded in the frequency-hoping states of RIS elements. Unlike the ORM-OFDM scheme, the FRM-OFDM scheme can achieve higher reflection efficiency, since the latter does not turn off any reflection element in reflection modulation. We propose a block coordinate descent (BCD) algorithm to maximize the user achievable rate for the FRM-OFDM system by jointly optimizing the phase shift of the RIS and the power allocation at the transmitter. Further, we design a bilinear message passing (BMP) algorithm for the bilinear recovery of both the user symbols and the RIS data. Numerical simulations have verified the efficiency of the designed BCD algorithm for system optimization and the BMP algorithm for signal detection, as well as the superiority of the proposed FRM-OFDM scheme over the ORM-OFDM scheme.
قيم البحث
اقرأ أيضاً
Reconfigurable intelligent surface (RIS) technology has recently emerged as a spectral- and cost-efficient approach for wireless communications systems. However, existing hand-engineered schemes for passive beamforming design and optimization of RIS,
such as the alternating optimization (AO) approaches, require a high computational complexity, especially for multiple-input-multiple-output (MIMO) systems. To overcome this challenge, we propose a low-complexity unsupervised learning scheme, referred to as learning-phase-shift neural network (LPSNet), to efficiently find the solution to the spectral efficiency maximization problem in RIS-aided MIMO systems. In particular, the proposed LPSNet has an optimized input structure and requires a small number of layers and nodes to produce efficient phase shifts for the RIS. Simulation results for a 16x2 MIMO system assisted by an RIS with 40 elements show that the LPSNet achieves 97.25% of the SE provided by the AO counterpart with more than a 95% reduction in complexity.
Given the proliferation of wireless sensors and smart mobile devices, an explosive escalation of the volume of data is anticipated. However, restricted by their limited physical sizes and low manufacturing costs, these wireless devices tend to have l
imited computational capabilities and battery lives. To overcome this limitation, wireless devices may offload their computational tasks to the nearby computing nodes at the network edge in mobile edge computing (MEC). At the time of writing, the benefits of MEC systems have not been fully exploited, predominately because the computation offloading link is still far from perfect. In this article, we propose to enhance MEC systems by exploiting the emerging technique of reconfigurable intelligent surfaces (RIS), which are capable of `reconfiguring the wireless propagation environments, hence enhancing the offloading links. The benefits of RISs can be maximized by jointly optimizing both the RISs as well as the communications and computing resource allocations of MEC systems. Unfortunately, this joint optimization imposes new research challenges on the system design. Against this background, this article provides an overview of RIS-assisted MEC systems and highlights their four use cases as well as their design challenges and solutions. Finally, their performance is characterized with the aid of a specific case study, followed by a range of future research ideas.
This article aims to reduce huge pilot overhead when estimating the reconfigurable intelligent surface (RIS) relayed wireless channel. Motivated by the compelling grasp of deep learning in tackling nonlinear mapping problems, the proposed approach on
ly activates a part of RIS elements and utilizes the corresponding cascaded channel estimate to predict another part. Through a synthetic deep neural network (DNN), the direct channel and active cascaded channel are first estimated sequentially, followed by the channel prediction for the inactive RIS elements. A three-stage training strategy is developed for this synthetic DNN. From simulation results, the proposed deep learning based approach is effective in reducing the pilot overhead and guaranteeing the reliable estimation accuracy.
Reconfigurable intelligent surfaces (RISs) have been recently considered as one of the emerging technologies for future communication systems by leveraging the tuning capabilities of their reflecting elements. In this paper, we investigate the potent
ial of an RIS-based architecture for uplink sensor data transmission in an ultra-reliable low-latency communication (URLLC) context. In particular, we propose an RIS-aided grant-free access scheme for an industrial control scenario, aiming to exploit diversity and achieve improved reliability performance. We consider two different resource allocation schemes for the uplink transmissions, i.e., dedicated and shared slot assignment, and three different receiver types, namely the zero-forcing, the minimum mean squared error (MMSE), and the MMSE-successive interference cancellation receivers. Our extensive numerical evaluation in terms of outage probability demonstrates the gains of our approach in terms of reliability, resource efficiency, and capacity and for different configurations of the RIS properties. An RIS-aided grant-free access scheme combined with advanced receivers is shown to be a well-suited option for uplink URLLC.
Wireless powered mobile edge computing (WP-MEC) has been recognized as a promising technique to provide both enhanced computational capability and sustainable energy supply to massive low-power wireless devices. However, its energy consumption become
s substantial, when the transmission link used for wireless energy transfer (WET) and for computation offloading is hostile. To mitigate this hindrance, we propose to employ the emerging technique of intelligent reflecting surface (IRS) in WP-MEC systems, which is capable of providing an additional link both for WET and for computation offloading. Specifically, we consider a multi-user scenario where both the WET and the computation offloading are based on orthogonal frequency-division multiplexing (OFDM) systems. Built on this model, an innovative framework is developed to minimize the energy consumption of the IRS-aided WP-MEC network, by optimizing the power allocation of the WET signals, the local computing frequencies of wireless devices, both the sub-band-device association and the power allocation used for computation offloading, as well as the IRS reflection coefficients. The major challenges of this optimization lie in the strong coupling between the settings of WET and of computing as well as the unit-modules constraint on IRS reflection coefficients. To tackle these issues, the technique of alternative optimization is invoked for decoupling the WET and computing designs, while two sets of locally optimal IRS reflection coefficients are provided for WET and for computation offloading separately relying on the successive convex approximation method. The numerical results demonstrate that our proposed scheme is capable of monumentally outperforming the conventional WP-MEC network without IRSs.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
