اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدNumerical simulation of non-isothermal viscoelastic flows at high Weissenberg numbers using a finite volume method on general unstructured meshes
69
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this numerical study, an original approach to simulate non-isothermal viscoelastic fluid flows at high Weissenberg numbers is presented. Stable computations over a wide range of Weissenberg numbers are assured by using the root conformation approach in a finite volume framework on general unstructured meshes. The numerical stabilization framework is extended to consider thermo-rheological properties in Oldroyd-B type viscoelastic fluids. The temperature dependence of the viscoelastic fluid is modeled with the time-temperature superposition principle. Both Arrhenius and WLF shift factors can be chosen, depending on the flow characteristics. The internal energy balance takes into account both energy and entropy elasticity. Partitioning is achieved by a constant split factor. An analytical solution of the balance equations in planar channel flow is derived to verify the results of the main field variables and to estimate the numerical error. The more complex entry flow of a polyisobutylene-based polymer solution in an axisymmetric 4:1 contraction is studied and compared to experimental data from the literature. We demonstrate the stability of the method in the experimentally relevant range of high Weissenberg numbers. The results at different imposed wall temperatures, as well as Weissenberg numbers, are found to be in good agreement with experimental data. Furthermore, the division between energy and entropy elasticity is investigated in detail with regard to the experimental setup.
قيم البحث
اقرأ أيضاً
We propose the rhoLENT method, an extension of the unstructured Level Set / Front Tracking (LENT) method, based on the collocated Finite Volume equation discretization, that recovers exact numerical stability for the two-phase momentum convection wit
h a range of density ratios, namely $rho^-/rho^+in [1, 10000]$. We provide the theoretical basis for the numerical inconsistency in the collocated finite volume equation discretization of the single-field two-phase momentum convection. The cause of the numerical inconsistency lies in the way the cell-centered density is computed in the new time step ($rho_c^{n+1}$). Specifically, if $rho_c^{n+1}$ is computed from the approximation of the fluid interface at $t^{n+1}$, and it is not computed by solving a mass conservation equation (or its equivalent), the two-phase momentum convection term will automatically be inconsistently discretized. We provide the theoretical justification behind using the auxiliary mass conservation equation to stabilize flows with strong density ratios. The evaluation of the face-centered (mass flux) density we base on the fundamental principle of mass conservation, used to model the single-field density, contrary to the use of different weighted averages of cell-centered single-field densities and alternative reconstructions of the mass flux density by other contemporary methods. Implicit discretization of the two-phase momentum convection term is achieved, removing the CFL stability criterion. Numerical stability is demonstrated in terms of the relative $L_infty$ velocity error norm with realistic viscosity and strong surface tension forces. The stabilization technique in the rhoLENT method is also applicable to other two-phase flow simulation methods that utilize the collocated unstructured Finite Volume Method to discretize single-field two-phase Navier-Stokes Equations.
Mesh-free methods have significant potential for simulations of flows in complex geometries, with the difficulties of domain discretisation greatly reduced. However, many mesh-free methods are limited to low order accuracy. In order to compete with c
onventional mesh-based methods, high order accuracy is essential. The Local Anisotropic Basis Function Method (LABFM) is a mesh-free method introduced in King et al., J. Comput. Phys. 415:109549 (2020), which enables the construction of highly accurate difference operators on disordered node discretisations. Here, we introduce a number of developments to LABFM, in the areas of basis function construction, stencil optimisation, stabilisation, variable resolution, and high order boundary conditions. With these developments, direct numerical simulations of the Navier Stokes equations are possible at extremely high order (up to 10th order in characteristic node spacing internally). We numerically solve the isothermal compressible Navier Stokes equations for a range of geometries: periodic and channel flows, flows past a cylinder, and porous media. Excellent agreement is seen with analytical solutions, published numerical results (using a spectral element method), and experiments. The potential of the method for direct numerical simulations in complex geometries is demonstrated with simulations of subsonic and transonic flows through an inhomogeneous porous media at pore Reynolds numbers up to Re=968.
The performance of interFoam (a widely used solver within OpenFOAM package) in simulating the propagation of water waves has been reported to be sensitive to the temporal and spatial resolution. To facilitate more accurate simulations, a numerical wa
ve tank is built based on a high-order accurate Navier-Stokes model, which employs the VPM (volume-average/point-value multi-moment) scheme as the fluid solver and the THINC/QQ method (THINC method with quadratic surface representation and Gaussian quadrature) for the free-surface capturing. Simulations of regular waves in an intermediate water depth are conducted and the results are assessed via comparing with the analytical solutions. The performance of the present model and interFoam solver in simulating the wave propagation is systematically compared in this work. The results clearly demonstrate that compared with interFoam solver, the present model significantly improves the dissipation properties of the propagating wave, where the waveforms as well as the velocity distribution can be substantially maintained while the waves propagating over long distances even with large time steps and coarse grids. It is also shown that the present model requires much less computation time to reach a given error level in comparison with interFoam solver.
Most fluid flow problems that are vital in engineering applications involve at least one of the following features: turbulence, shocks, and/or material interfaces. While seemingly different phenomena, these flows all share continuous generation of hi
gh wavenumber modes, which we term the $k_infty$ irregularity. In this work, an inviscid regularization technique called observable regularization is proposed for the simulation of two-phase compressible flows. The proposed approach regularizes the equations at the level of the partial differential equation and as a result, any numerical method can be used to solve the system of equations. The regularization is accomplished by introducing an observability limit that represents the length scale below which one cannot properly model or continue to resolve flow structures. An observable volume fraction equation is derived for capturing the material interface, which satisfies the pressure equilibrium at the interface. The efficacy of the observable regularization method is demonstrated using several test cases, including a one-dimensional material interface tracking, one-dimensional shock-tube and shock-bubble problems, and two-dimensional simulations of a shock interacting with a cylindrical bubble. The results show favorable agreement, both qualitatively and quantitatively, with available exact solutions or numerical and experimental data from the literature. The computational saving by using the current method is estimated to be about one order of magnitude in two-dimensional computations and significantly higher in three-dimensional computations. Lastly, the effect of the observability limit and best practices to choose its value are discussed.
This work presents a new multiphase SPH model that includes the shifting algorithm and a variable smoothing length formalism to simulate multi-phase flows with accuracy and proper interphase management. The implementation was performed in the DualSPH
ysics code and validated for different canonical experiments, such as the single-phase and multiphase Poiseuille and Couette test cases. The method is accurate even for the multiphase case for which two phases are simulated. The shifting algorithm and the variable smoothing length formalism has been applied in the multiphase SPH model to improve the numerical results at the interphase even when it is highly deformed and non-linear effects become important. The obtained accuracy in the validation tests and the good interphase definition in the instability cases indicate an important improvement in the numerical results compared with single-phase and multiphase models where the shifting algorithm and the variable smoothing length formalism are not applied.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
