اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe influence of material properties and process parameters on the spreading process in additive manufacturing
82
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Laser powder bed fusion (LPBF) is an additive manufacturing (AM) technology. To achieve high product quality, the powder is best spread as a uniform, dense layer. The challenge for LPBF manufacturers is to develop a spreading process that can produce a consistent layer quality for the many powders used, which show considerable differences in spreadability. Therefore, we investigate the influence of material properties, process parameters and the type of spreading tool on the layer quality. The discrete particle method is used to simulate the spreading process and to define metrics to evaluate the powder layer characteristics. We found that particle shape and surface roughness in terms of rolling resistance and interparticle sliding friction as well as particle cohesion all have a major (sometimes surprising) influence on the powder layer quality: more irregular shaped particles, rougher particle surfaces and/or higher interfacial cohesion usually, but not always, lead to worse spreadability. Our findings illustrate that there is a trade-off between material properties and process parameters. Increasing the spreading speed decreases layer quality for non- and weakly cohesive powders, but improves it for strongly cohesive ones. Using a counter-clockwise rotating roller as a spreading tool improves the powder layer quality compared to spreading with a blade. Finally, for both geometries, a unique correlation between the quality criteria uniformity and mass fraction is reported and some of the findings are related to size-segregation during spreading.
قيم البحث
اقرأ أيضاً
An investigation on the additive manufacturing and the experimental testing of 3D models of tensegrity prisms and columns is presented. An electron beam melting facility (Arcam EBM S12) is employed to 3D print structures composed of tensegrity prisms
endowed with rigid bases and temporary supports, which are made out of the titanium alloy Ti6Al4V. The temporary supports are removed after the additive manufacturing phase, when Spectra cross-strings are added to the 3D printed models, and a suitable state of internal prestress is applied to the structure. The experimental part of the study shows that the examined structures feature sitffening-type elastic response under large or moderately large axial strains induced by compressive loading. Such a geometrically nonlinear behavior confirms previous theoretical results available in the literature, and paves the way to the use of tensegrity prisms and columns as innovative mechanical metamaterials and smart devices.
Plastic scintillator detectors are widely used in particle physics thanks to the very good particle identification, tracking capabilities and time resolution. However, new experimental challenges and the need for enhanced performance require the cons
truction of detector geometries that are complicated using the current production techniques. In this article we propose a new production technique based on additive manufacturing that aims to 3D print polystyrene-based scintillator. The production process and the results of the scintillation light output measurement of the 3D-printed scintillator are reported.
The future of space exploration missions will rely on technologies increasing their endurance and self-sufficiency, including for manufacturing objects on-demand. We propose a process for handling and additively manufacturing powders that functions i
ndependently of the gravitational environment and with no restriction on feedstock powder flowability. Based on a specific sequence of boundary loads applied to the granular packing, powder is transported to the printing zone, homogenized and put under compression to increase the density of the final part. The powder deposition process is validated by simulations that show the homogeneity and density of deposition to be insensitive to gravity and cohesion forces within the DEM model. We further provide an experimental proof of concept of the process by successfully 3D printing parts on-ground and in weightlessness, on parabolic flight. Powders exhibiting high and low flowability are used as model feedstock material to demonstrate the versatility of the process, opening the way for additive manufacturing of recycled material.
Wire-feed laser additive manufacturing (WLAM) is gaining wide interest due to its high level of automation, high deposition rates, and good quality of printed parts. In-process monitoring and feedback controls that would reduce the uncertainty in the
quality of the material are in the early stages of development. Machine learning promises the ability to accelerate the adoption of new processes and property design in additive manufacturing by making process-structure-property connections between process setting inputs and material quality outcomes. The molten pool dimensional information and temperature are the indicators for achieving the high quality of the build, which can be directly controlled by processing parameters. For the purpose of in situ quality control, the process parameters should be controlled in real-time based on sensed information from the process, in particular the molten pool. Thus, the molten pool-process relations are of preliminary importance. This paper analyzes experimentally collected in situ sensing data from the molten pool under a set of controlled process parameters in a WLAM system. The variations in the steady-state and transient state of the molten pool are presented with respect to the change of independent process parameters. A multi-modality convolutional neural network (CNN) architecture is proposed for predicting the control parameter directly from the measurable molten pool sensor data for achieving desired geometric and microstructural properties. Dropout and regularization are applied to the CNN architecture to avoid the problem of overfitting. The results highlighted that the multi-modal CNN, which receives temperature profile as an external feature to the features extracted from the image data, has improved prediction performance compared to the image-based uni-modality CNN approach.
We consider the dynamics of a suspension of hard sphere-like particles in the proximity of its glass transition, the region where the intermediate scattering functions show significant aging. The time correlation function of the longitudinal particle
current shows no dependence on age and reveals behaviour of ideal super-packed fluid and glass. The power laws of the beta process of the idealised mode coupling theory are exposed directly without reliance on fitting parameters. We proffer a mechanism linking the reversible/ageless dynamics, which constitutes the beta-process, and the irreversible aging dynamics. The latter verifies predictions of spin-glass theories.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
