اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدPolystyrene-based nanocomposites with different fillers: fabrication and mechanical properties
204
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The paper presents a comprehensive analysis of elastic properties of polystyrene-based nanocomposites filled with different types of inclusions: small spherical particles (SiO2 and Al2O3), alumosilicates (montmorillonite, halloysite natural tubules and Mica) and carbon nanofillers (carbon black and multi-walled carbon nanotubes). Composites were fabricated by melt technology. The analysis of composite melts showed that the introduction of Montmorillonite, Multi-walled carbon nanotubes, and Al2O3 particles provided an increase in melt viscosity by an average of 2 to 5 orders of magnitude over the pure polystyrene. Block samples of composites with different filler concentrations were prepared, and their linear and nonlinear elastic properties were studied. The introduction of more rigid particles led to a more profound increase in the elastic modulus of the composite, with the highest rise of about 80% obtained with carbon fillers. Carbon black particles provided also an enhanced strength at break of about 20% higher than that of pure polystyrene. The nonlinear elastic moduli of composites were shown to be more sensitive to addition of filler particles to the polymer matrix than the linear ones. The nonlinearity coefficient $beta$ comprising the combination of linear and nonlinear elastic moduli of a material demonstrated considerable changes correlating with changes of the Youngs modulus. The absolute value of $beta$ showed rise in 1.5-1.6 times in the CB- and HNT-containing composites as compared to that of pure PS. The changes in nonlinear elasticity of fabricated composites were compared with measurements of the parameters of bulk nonlinear strain waves in them. Variations of wave velocity and decay decrement correlated with observed enhancement of materials nonlinearity.
قيم البحث
اقرأ أيضاً
Mechanical metamaterials are architected manmade materials that allow for unique behaviors not observed in nature, making them promising candidates for a wide range of applications. Existing metamaterials lack tunability as their properties can only
be changed to a limited extent after the fabrication. In this paper, we present a new magneto-mechanical metamaterial that allows great tunability through a novel concept of deformation mode branching. The architecture of this new metamaterial employs an asymmetric joint design using hard-magnetic soft active materials that permits two distinct actuation modes (bending and folding) under opposite-direction magnetic fields. The subsequent application of mechanical forces leads to the deformation mode branching where the metamaterial architecture transforms into two distinctly different shapes, which exhibit very different deformations and enable great tunability in properties such as mechanical stiffness and acoustic bandgaps. Furthermore, this metamaterial design can be incorporated with magnetic shape memory polymers with global stiffness tunability, which further enables the global shift of the acoustic behaviors. The combination of magnetic and mechanical actuations, as well as shape memory effects, imbue unmatched tunable properties to a new paradigm of metamaterials.
Polystyrene-based phosphorene nanocomposites were prepared by a solvent blending procedure allowing the embedding of black phosphorus (BP) nanoflakes in the polymer matrix. Raman spectroscopy, X Ray Diffraction and TEM microscopy were employed to cha
racterize the structural and the morphological characteristics of the achieved hybrids, with the aim to evaluate the dispersion level of black phosphorus layers. TGA, DSC analysis as well as thermal oxidation and photo-degradation techniques were employed to investigate the thermal- and the photo-stability of the samples. The collected results evidenced better thermal and photostability of both polymer matrix and dispersed layered phosphorus, suggesting really interesting polymer-nanofiller synergic effects ascribable to the presence and the good dispersion of the 2D-nanomaterial.
We present several recently synthesized nanocomposites consisting of liquid crystals as well as an organic molecular crystal embedded into the nanochannels of mesoporous alumina and silica. As liquid-crystalline mesogens achiral, nematogen and chiral
cholesteric guest molecules infiltrated into nanochannels by spontaneous imbibition were chosen. The molecular ordering inside the nanochannels, which can be tailored by modifying the surface anchoring, was characterized by optical polarimetry (linear and/or circular birefringence) in combination with X-ray diffraction. For the synthesis of the solid crystalline nanocomposites ferroelectric triglycine sulfate (TGS) nanocrystals were deposited into the nanochannels by slow evaporation of saturated water solutions imbibed into the porous hosts. Their textural and physicochemical properties were explored by x-ray diffraction, scanning electron microscopy and dielectric techniques.
Specific strength (strength/density) is a crucial factor while designing high load bearing architecture in areas of aerospace and defence. Strength of the material can be enhanced by blending with high strength component or, by compositing with high
strength fillers but both the options has limitations such as at certain load, materials fail due to poor filler and matrix interactions. Therefore, researchers are interested in enhancing strength of materials by playing with topology/geometry and therefore nature is best option to mimic for structures whereas, complexity limits nature mimicked structures. In this paper, we have explored Zeolite-inspired structures for load bearing capacity. Zeolite-inspired structure were obtained from molecular dynamics simulation and then fabricated via Fused deposition Modeling. The atomic scale complex topology from simulation is experimentally synthesized using 3D printing. Compressibility of as-fabricated structures was tested in different direction and compared with simulation results. Such complex architecture can be used for ultralight aerospace and automotive parts.
Improving lithium-ion batteries (LIBs) safety remains in a challenging task when compared with the tremendous progress made in their performance in recent years. Embedding thermo-responsive polymer switching materials (TRPS) into LIB cells has been p
roved to be a promising strategy to provide consistent thermal abuse protections at coin-cell level. However, it is unrealistic to achieve large-scale applications without further demonstration in high-capacity pouch cells. Here, we employed tungsten carbide (WC) as a novel conductive filler, and successfully overcame the intrinsic processing difficulty of polyethylene (PE) matrix in a scalable solvent-based method to obtain ultra-thin, uniform, highly conductive TRPS. Moreover, by integrating TRPS directly into LIB electrodes, no extra fabrication facilities or processes are required for making the cells. As a result, multi-layer pouch cells with consistent electrochemical performance and thermal abuse protection function were fabricated using industry relevant manufacturing techniques, which brings TRPS one step further to the real application scenarios.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
