اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدQuantization bias for digital correlators
120
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In radio interferometry, the quantization process introduces a bias in the magnitude and phase of the measured correlations which translates into errors in the measurement of source brightness and position in the sky, affecting both the system calibration and image reconstruction. In this paper we investigate the biasing effect of quantization in the measured correlation between complex-valued inputs with a circularly symmetric Gaussian probability density function (PDF), which is the typical case for radio astronomy applications. We start by calculating the correlation between the input and quantization error and its effect on the quantized variance, first in the case of a real-valued quantizer with a zero mean Gaussian input and then in the case of a complex-valued quantizer with a circularly symmetric Gaussian input. We demonstrate that this input-error correlation is always negative for a quantizer with an odd number of levels, while for an even number of levels this correlation is positive in the low signal level regime. In both cases there is an optimal interval for the input signal level for which this input-error correlation is very weak and the model of additive uncorrelated quantization noise provides a very accurate approximation. We determine the conditions under which the magnitude and phase of the measured correlation have negligible bias with respect to the unquantized values: we demonstrate that the magnitude bias is negligible only if both unquantized inputs are optimally quantized (i.e., when the uncorrelated quantization error model is valid), while the phase bias is negligible when 1) at least one of the inputs is optimally quantized, or when 2) the correlation coefficient between the unquantized inputs is small. Finally, we determine the implications of these results for radio interferometry.
قيم البحث
اقرأ أيضاً
Superconductor electronics fabrication technology developed at MIT Lincoln Laboratory enables the development of VLSI digital circuits with millions of Josephson junctions per square centimeter. However, conventional DC and multi-phase AC biasing tec
hniques already encounter serious challenges for scaling circuits above several hundred thousand junctions. In this work, we propose a novel AC-based biasing scheme for RSFQ-type logic families requiring DC bias. The major step toward this scheme is a superconducting AC/DC rectifier which we introduced at ASC 2014. Initially, we proposed to connect the rectifiers to payload cells via superconducting inductors with large inductance in order to reduce parasitic effects of flux quantization. Recently, we discovered that this powering scheme works even better at a much lower value of the inductance, when it is just sufficient to hold only one or two flux quanta in the inductive loop between the converter and the payload. In this case, flux quantization in the loop becomes beneficial because the value of current fed into the payload is defined by the value of the coupling inductance. Therefore, our AC/SFQ converter powers the payload cell by a single flux quantum rather than by DC current. Such mode of operation is extremely energy efficient because the energy is used only to recover flux quantum consumed by the cell during the logic operation. We present designs of AC/SFQ converters comprising an AC/DC rectifier and a current conditioning circuit which we termed an SFQ filter. We also present test results and demonstrate AC/SFQ powering a payload circuit using circuits fabricated in a new, 150-nm node of Lincoln Laboratory fabrication technology using self-shunted Nb/AlOx-Al/Nb Josephson junctions with 600 $mu$A/$mu$$m^2$ critical current density and 200 nm minimum linewidth of inductors.
We describe an hierarchical, frequency-domain beamforming architecture for synthesising a sky beam from the wideband antenna feeds of digital aperture arrays. The development of densely-packed, all-digital aperture arrays is an important area of rese
arch required for the Square Kilometre Array (SKA) radio telescope. The design of real-time signal processing systems for digital aperture arrays is currently a central challenge in pathfinder projects worldwide. In particular, this work describes a specific implementation of the beamforming architecture to the 2-Polarisation All-Digital (2-PAD) aperture array demonstrator.
The future Cherenkov Telescope Array (CTA) will consist of several tens of telescopes of different mirror sizes. CTA will provide next generation sensitivity to very high energy photons from few tens of GeV to >100 TeV. Several focal plane instrument
ation options are currently being evaluated inside the CTA consortium. In this paper, the current status of the FlashCam prototyping project is described. FlashCam is based on a fully digital camera readout concept and features a clean separation between photon detector plane and signal digitization/triggering electronics.
An FPGA-based digital-receiver has been developed for a low-frequency imaging radio interferometer, the Murchison Widefield Array (MWA). The MWA, located at the Murchison Radio-astronomy Observatory (MRO) in Western Australia, consists of 128 dual-po
larized aperture-array elements (tiles) operating between 80 and 300,MHz, with a total processed bandwidth of 30.72 MHz for each polarization. Radio-frequency signals from the tiles are amplified and band limited using analog signal conditioning units; sampled and channelized by digital-receivers. The signals from eight tiles are processed by a single digital-receiver, thus requiring 16 digital-receivers for the MWA. The main function of the digital-receivers is to digitize the broad-band signals from each tile, channelize them to form the sky-band, and transport it through optical fibers to a centrally located correlator for further processing. The digital-receiver firmware also implements functions to measure the signal power, perform power equalization across the band, detect interference-like events, and invoke diagnostic modes. The digital-receiver is controlled by high-level programs running on a single-board-computer. This paper presents the digital-receiver design, implementation, current status, and plans for future enhancements.
The Arcminute Microkelvin Imager (AMI) telescopes located at the Mullard Radio Astronomy Observatory near Cambridge have been significantly enhanced by the implementation of a new digital correlator with 1.2 MHz spectral resolution. This system has r
eplaced a 750-MHz resolution analogue lag-based correlator, and was designed to mitigate the effects of radio frequency interference, particularly from geostationary satellites that contaminate observations at low declinations. The upgraded instrument consists of 18 ROACH2 Field Programmable Gate Array platforms used to implement a pair of real-time FX correlators -- one for each of AMIs two arrays. The new system separates the down-converted RF baseband signal from each AMI receiver into two 2.3 GHz-wide sub-bands which are each digitized at 5-Gsps with 8 bits of precision. These digital data streams are filtered into 2048 frequency channels and cross-correlated using FPGA hardware, with a commercial 10 Gb Ethernet switch providing high-speed data interconnect. Images formed using data from the new digital correlator show over an order of magnitude improvement in dynamic range over the previous system. The ability to observe at low declinations has also been significantly improved.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
