اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدMolecular Beam Epitaxy Growth of Tetragonal FeS Film on SrTiO3(001) Substrate
93
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report the successful growth of tetragonal FeS film with one or two unit-cell (UC) thickness on SrTiO3(001) substrate by molecular beam epitaxy. Large lattice constant mismatch with the substrate leads to high density of defects in single UC FeS, while it has been significantly reduced in double UC thick film due to the lattice relaxation. The scanning tunneling spectra on the surface of FeS thin film reveal the electronic doping effect of single UC FeS from the substrate. In addition, at the Fermi level, the energy gaps of approximate 1.5 meV are observed in films of both thicknesses at 4.6 K and below. The absence of coherence peaks of gap spectra may be related to the preformed Cooper-pairs without phase coherence.
قيم البحث
اقرأ أيضاً
The stoichiometric 111 iron-based superconductor, LiFeAs, has attacted great research interest in recent years. For the first time, we have successfully grown LiFeAs thin film by molecular beam epitaxy (MBE) on SrTiO3(001) substrate, and studied the
interfacial growth behavior by reflection high energy electron diffraction (RHEED) and low-temperature scanning tunneling microscope (LT-STM). The effects of substrate temperature and Li/Fe flux ratio were investigated. Uniform LiFeAs film as thin as 3 quintuple-layer (QL) is formed. Superconducting gap appears in LiFeAs films thicker than 4 QL at 4.7 K. When the film is thicker than 13 QL, the superconducting gap determined by the distance between coherence peaks is about 7 meV, close to the value of bulk material. The ex situ transport measurement of thick LiFeAs film shows a sharp superconducting transition around 16 K. The upper critical field, Hc2(0)=13.0 T, is estimated from the temperature dependent magnetoresistance. The precise thickness and quality control of LiFeAs film paves the road of growing similar ultrathin iron arsenide films.
Hole-doped perovskite bismuthates such as Ba$_{1-x}$K$_x$BiO$_3$ and Sr$_{1-x}$K$_x$BiO$_3$ are well-known bismuth-based oxide high-transition-temperature superconductors. Reported thin bismuthate films show relatively low quality, likely due to thei
r large lattice mismatch with the substrate and a low sticking coefficient of Bi at high temperatures. Here, we report the successful epitaxial thin film growth of the parent compound strontium bismuthate SrBiO$_3$ on SrO-terminated SrTiO$_3$ (001) substrates by molecular beam epitaxy. Two different growth methods, high-temperature co-deposition or recrystallization cycles of low-temperature deposition plus high-temperature annealing, are developed to improve the epitaxial growth. SrBiO$_3$ has a pseudocubic lattice constant $sim$4.25 AA, an $sim$8.8% lattice mismatch on SrTiO$_3$ substrate, leading to a large strain in the first few unit cells. Films thicker than 6 unit cells prepared by both methods are fully relaxed to bulk lattice constant and have similar quality. Compared to high-temperature co-deposition, the recrystallization method can produce higher quality 1-6 unit cell films that are coherently or partially strained. Photoemission experiments reveal the bonding and antibonding states close to the Fermi level due to Bi and O hybridization, in good agreement with density functional theory calculations. This work provides general guidance to the synthesis of high-quality perovskite bismuthate films.
We report growth of superconducting Sr2RuO4 films by oxide molecular beam epitaxy (MBE). Careful tuning of the Ru flux with an electron beam evaporator enables us to optimize growth conditions including the Ru/Sr flux ratio and also to investigate st
oichiometry effects on the structural and transport properties. The highest onset transition temperature of about 1.1 K is observed for films grown in a slightly Ru-rich flux condition in order to suppress Ru deficiency. The realization of superconducting Sr2RuO4 films via oxide MBE opens up a new route to study the unconventional superconductivity of this material.
We report on the epitaxial growth and surface structure of infinite-layer cuprate Sr1-xNdxCuO2 films on SrTiO3(001) substrates by combining ozone-assisted molecular beam epitaxy and in situ scanning tunneling microscopy. Careful substrate temperature
and flux control has been used to achieve single-phase, stoichiometric, and c-axis oriented films. The surface of the films is usually characterized by a mixed CuO2 surface and gridlike superstructure. The superstructure exhibits a periodicity of 3.47 nm that corresponds to a coincidence lattice between the overlayer peroxide SrO2 and underlying CuO2 plane, and gives rise to a conductance spectrum that is distinct from the Mott-Hubbard band structure of CuO2. At a higher Nd composition x > 0.1, a (2 x 2) surface characteristic of the hole-doped CuO2 emerges, which we ascribe to the intake of apical oxygens in the intervening Sr planes.
Epitaxial films of NdFeAsO were grown on GaAs substrates by molecular beam epitaxy (MBE). All elements including oxygen were supplied from solid sources using Knudsen cells. The x-ray diffraction pattern of the film prepared with the optimum growth c
ondition showed no indication of impurity phases. Only (00l) peaks were observed, indicating that NdFeAsO was grown with the c-axis perpendicular to the substrate. The window of optimum growth condition was very narrow, but the NdFeAsO phase was grown with a very good reproducibility. Despite the absence of any appreciable secondary phase, the resistivity showed an increase with decreasing temperature.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
