اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEffects of stretching on the frictional stress of rubber
109
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper, we report on new experimental results on the effects of in-plane surface stretching on the friction of Poly(DiMethylSiloxane) (PDMS) rubber with smooth rigid probes. Friction-induced displacement fields are measured at the surface of the PDMS substrate under steady-state sliding. Then, the corresponding contact pressure and frictional stress distributions are determined from an inversion procedure. Using this approach, we show that the local frictional stress $tau$ is proportional to the local stretch ratio $lambda$ at the rubber surface. Additional data using a triangular flat punch indicate that $tau(lambda)$ relationship is independent on the contact geometry. From friction experiments using pre-stretched PDMS substrate, it is also found that the stretch-dependence of the frictional stress is isotropic, i.e. it does not depend on the angle between stretching and sliding directions. Potential physical explanations for this phenomenon are provided within the framework of Schallamachs friction model. Although the present experiments are dealing with smooth contact interfaces, the reported $tau(lambda)$ dependence is also relevant to the friction of statistically rough contact interfaces, while not accounted for in related contact mechanics models.
قيم البحث
اقرأ أيضاً
This paper addresses the issue of the determination of the frictional stress distribution from the inversion of the measured surface displacement field for sliding interfaces between a glass lens and a rubber (poly(dimethylsiloxane)) substrate. Exper
imental results show that high lateral strains are achieved at the periphery of the sliding contacts. As a consequence, an accurate inversion of the displacement field requires that finite strains and non linear response of the rubber substrate are taken into account. For that purpose, a Finite Element (FE) inversion procedure is implemented where the measured displacement field is applied as a boundary condition at the upper surface of a meshed body representing the rubber substrate. Normal pressure is also determined by the same way, if non-diverging values are assumed at the contact edge. This procedure is applied to linearly sliding contacts as well as on twisting contacts.
We report a dynamical-mechanical study of stress relaxation at small deformation in a natural (polyisoprene) rubber well above its glass transition temperature Tg. We find that an almost complete relaxation of stress takes place over very long period
s of time, even though the elastic network integrity is fully retained. The relaxation rate and the long-time equilibrium modulus are sensitive functions of temperature which do not follow time-temperature superposition. Many characteristic features of non-ergodic ageing response are apparent at both short and very long times. We interpret the observed behaviour in terms of the properties of rubber crosslinks, capable of isomerisation under stress, and relate the results to recent models of soft glassy rheology.
We present measurements of the stress response of packings formed from a wide range of particle shapes. Besides spheres these include convex shapes such as the Platonic solids, truncated tetrahedra, and triangular bipyramids, as well as more complex,
non-convex geometries such as hexapods with various arm lengths, dolos, and tetrahedral frames. All particles were 3D-printed in hard resin. Well-defined initial packing states were established through preconditioning by cyclic loading under given confinement pressure. Starting from such initial states, stress-strain relationships for axial compression were obtained at four different confining pressures for each particle type. While confining pressure has the largest overall effect on the mechanical response, we find that particle shape controls the details of the stress-strain curves and can be used to tune packing stiffness and yielding. By correlating the experimentally measured values for the effective Youngs modulus under compression, yield stress and energy loss during cyclic loading, we identify trends among the various shapes that allow for designing a packings aggregate behavior.
A MEMS-based sensing device is used to measure the normal and tangential stress fields at the base of a rough elastomer film in contact with a smooth glass cylinder in steady sliding. This geometry allows for a direct comparison between the stress pr
ofiles measured along the sliding direction and the predictions of an original textit{exact} bidimensional model of friction. The latter assumes Amontons friction law, which implies that in steady sliding the interfacial tangential stress is equal to the normal stress times a pressure-independent dynamic friction coefficient $mu_d$, but makes no further assumption on the normal stress field. Discrepancy between the measured and calculated profiles is less than 14% over the range of loads explored. Comparison with a test model, based on the classical assumption that the normal stress field is unchanged upon tangential loading, shows that the exact model better reproduces the experimental profiles at high loads. However, significant deviations remain that are not accounted for by either calculations. In that regard, the relevance of two other assumptions made in the calculations, namely (i) the smoothness of the interface and (ii) the pressure-independence of $mu_d$ is briefly discussed.
In rubber friction studies it is often observed that the kinetic friction coefficient {mu} depends on the nominal contact pressure p. We discuss several possible origins of the pressure dependency of {mu}: (a) saturation of the contact area (and fric
tion force) due to high nominal squeezing pressure, (b) non-linear viscoelasticity, (c) non-randomness in the surface topography, in particular the influence of the skewness of the surface roughness profile, (d) adhesion, and (e) frictional heating. We show that in most cases the non-linearity in the {mu}(p) relation is mainly due to process (e) (frictional heating), which softens the rubber, increases the area of contact, and (in most cases) reduces the viscoelastic contribution to the friction. In fact, since the temperature distribution in the rubber at time t depends on on the sliding history (i.e., on the earlier time t0 < t), the friction coefficient at time t will also depend on the sliding history, i.e. it is, strictly speaking, a time integral operator. The energy dissipation in the contact regions between solids in sliding contact can result in high local temperatures which may strongly affect the area of real contact and the friction force (and the wear-rate). This is the case for rubber sliding on road surfaces at speeds above 1 mm/s. In Ref. [14] we have derived equations which describe the frictional heating for solids with arbitrary thermal properties. In this paper the theory is applied to rubber friction on road surfaces. Numerical results are presented and compared to experimental data. We observe good agreement between the calculated and measured temperature increase.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
