اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدMechanical Properties of Norway Spruce: Intra-Ring Variation and Generic Behavior of Earlywood and Latewood until Failure
66
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The alternating earlywood and latewood growth ring structure has a strong influence on the mechanical performance of Norway spruce. In the current study, tensile tests in the longitudinal and tangential directions were performed on a series of specimens representing one growth ring at varying relative humidities. All tested mechanical parameters, namely modulus of elasticity and ultimate tensile stress, followed the density distribution in the growth ring, with the minimum values in earlywood and the maximum values in latewood. The samples were conditioned at three the relative humidities 50%, 65% and 95%. With increasing relative humidity, the values of the mechanical parameters were found to decrease. However, due to the high local variability, this decrease was not statistically significant. The test in the tangential direction on a set of earlywood and latewood specimens at 65% relative humidity revealed a similar limit of linear elasticity for both early- and latewood. Where the strength of both tissues was equal, the strain at failure was significantly greater for earlywood. Furthermore, the portion of the non-linear stress/strain behavior for earlywood was significantly greater. A Weibull analysis on the ultimate tensile strength revealed a tissue-independent Weibull modulus, which indicates similar defect distributions. For both, the failure occurred in the middle lamella.
قيم البحث
اقرأ أيضاً
The transverse hygro-expansion of the Norway spruce wood is studied on the growth ring level using digital image correlation. This non-destructive technique offers the possibility to contactless study deformation fields of relatively large areas. The
measured full-field strains are segmented into individual growth rings. Whereas radial strains closely follow the density progression with the maximum in the dense latewood, tangential and shear strain remain constant except for positions around the edges of the sample. A simple FE three phase growth ring model is in good agreement with the experimental values. The selective activation of individual phases like earlywood, transitionwood and latewood demonstrates that the radial hygro-expansion is dominated by the earlywood deformation, whereas tangential deformation is a complex interplay of expansion and compression that needs all tissues to fully develop.
The failure of adhesive bondlines has been studied at the microscopic level via tensile tests. Stable crack propagation could be generated by means of samples with improved geometry, which made in-situ observations possible. The interaction of cracks
with adhesive bondlines under various angles to the crack propagation was the focus of this study as well as the respective loading situations for the adhesives UF, PUR, and PVAc, which have distinctly different mechanical behaviors. It is shown how adhesive properties influence the occurrence of certain failure mechanisms and determine their appearance and order of magnitude. With the observed failure mechanisms, it becomes possible to predict the propagation path of a crack through the specimen.
We investigated through fully atomistic molecular dynamics simulations, the mechanical behavior (compressive and tensile) and energy absorption properties of two families (primitive (P688 and P8bal) and gyroid (G688 and G8bal)) of carbon-based schwar
zites. Our results show that all schwarzites can be compressed (with almost total elastic recovery) without fracture to more than 50%, one of them can be even remarkably compressed up to 80%. One of the structures (G8bal) presents negative Poissons ratio value (auxetic behavior). The crush force efficiency, the stroke efficiency and the specific energy absorption (SEA) values show that schwarzites can be effective energy absorber materials. Although the same level of deformation without fracture observed in the compressive case is not observed for the tensile case, it is still very high (30-40%). The fracture dynamics show extensive structural reconstructions with the formation of linear atomic chains (LACs).
We report first principle calculations of electronic and mechanical properties of few-layer borophene with the inclusion of interlayer van der Waals (vdW) interaction. The anisotropic metallic behaviors are preserved from monolayer to few-layer struc
tures. The energy splitting of bilayer borophene at $Gamma$ point near the Fermi level is about 1.7 eV, much larger than the values (0.5--1 eV) of other layered semiconductors, indicating much stronger vdW interactions in metallic layered borophene. In particular, the critical strains are enhanced by increasing the number of layers, leading to much more flexibility than that of monolayer structure. On the one hand, because of the buckled atomic structures, the out-of-plane negative Poissons ratios are preserved as the layer-number increases. On the other hand, we find that the in-plane negative Poissons ratios disappear in layered borophene, which is very different from puckered black phosphorus. The negative Poissons ratio will recover if we enlarge the interlayer distance to 6.3 $mboxAA$, indicating that the physical origin behind the change of Poissons ratios is the strong interlayer vdW interactions in layered borophene.
We report the synthesis of Y-substituted Mg-Zn ferrites using conventional standard ceramic technique. XRD patterns confirm the single phase cubic spinel structure up to x = 0.03 and appearance of a secondary phase of YFeO3for higher Y contents. FESE
M images depict the distribution of grains and EDS spectra confirmed the absence of any unwanted element. Completion of solid state reaction and formation of spinel structure has been revealed from FTIR spectra. The FTIR data along with lattice constant, bulk density and porosity were further used to calculate the stiffness constant (Cij), elastic constant and Debye temperatures. Mechanical stability of all studied compositions is confirmed from Cij using Born stability conditions. Brittleness and isotropic nature are also confirmed using Poisson ratio and anisotropy constants, respectively. The enhancement of dc electrical resistivity with Y content is observed. The energy band gap (increased with Y contents) is found in good agreement with dc electrical resistivity. Ferrimagnetic to paramagnetic phase change has been observed from the field dependent high temperature magnetization curves. The magnetic moments and saturation magnetization were found to be decreased with increasing temperature. The Curie temperature (Tc) has been measured from temperature dependent magnetic moment (M-T) and initial permeability and found to be in good agreement with each other. Decrease in Tc with Y content is due to redistribution of cations and weakening of the exchange coupling constant. The magnetic phase transition has been analyzed by Arrott plot and found to have second order phase transition. The dc resistivity endorses the prepared ferrites are suitable for high frequency and high temperature magnetic device applications as well.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
