اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEnergy Efficiency and Sum Rate Tradeoffs for Massive MIMO Systems with Underlaid Device-to-Device Communications
260
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper, we investigate the coexistence of two technologies that have been put forward for the fifth generation (5G) of cellular networks, namely, network-assisted device-to-device (D2D) communications and massive MIMO (multiple-input multiple-output). Potential benefits of both technologies are known individually, but the tradeoffs resulting from their coexistence have not been adequately addressed. To this end, we assume that D2D users reuse the downlink resources of cellular networks in an underlay fashion. In addition, multiple antennas at the BS are used in order to obtain precoding gains and simultaneously support multiple cellular users using multiuser or massive MIMO technique. Two metrics are considered, namely the average sum rate (ASR) and energy efficiency (EE). We derive tractable and directly computable expressions and study the tradeoffs between the ASR and EE as functions of the number of BS antennas, the number of cellular users and the density of D2D users within a given coverage area. Our results show that both the ASR and EE behave differently in scenarios with low and high density of D2D users, and that coexistence of underlay D2D communications and massive MIMO is mainly beneficial in low densities of D2D users.
قيم البحث
اقرأ أيضاً
This paper investigates user cooperation in massive multiple-input multiple-output (MIMO) systems with cascaded precoding. The high-dimensional physical channel in massive MIMO systems can be converted into a low-dimensional effective channel through
the inner precoder to reduce the overhead of channel estimation and feedback. The inner precoder depends on the spatial covariance matrix of the channels, and thus the same precoder can be used for different users as long as they have the same spatial covariance matrix. Spatial covariance matrix is determined by the surrounding environment of user terminals. Therefore, the users that are close to each other will share the same spatial covariance matrix. In this situation, it is possible to achieve user cooperation by sharing receiver information through some dedicated link, such as device-to-device communications. To reduce the amount of information that needs to be shared, we propose a decoding codebook based scheme, which can achieve user cooperation without the need of channel state information. Moreover, we also investigate the amount of bandwidth required to achieve efficient user cooperation. Simulation results show that user cooperation can improve the capacity compared to the non-cooperation scheme.
This paper proposes to deploy multiple reconfigurable intelligent surfaces (RISs) in device-to-device (D2D)-underlaid cellular systems. The uplink sum-rate of the system is maximized by jointly optimizing the transmit powers of the users, the pairing
of the cellular users (CUs) and D2D links, the receive beamforming of the base station (BS), and the configuration of the RISs, subject to the power limits and quality-of-service (QoS) of the users. To address the non-convexity of this problem, we develop a new block coordinate descent (BCD) framework which decouples the D2D-CU pairing, power allocation and receive beamforming, from the configuration of the RISs. Specifically, we derive closed-form expressions for the power allocation and receive beamforming under any D2D-CU pairing, which facilitates interpreting the D2D-CU pairing as a bipartite graph matching solved using the Hungarian algorithm. We transform the configuration of the RISs into a quadratically constrained quadratic program (QCQP) with multiple quadratic constraints. A low-complexity algorithm, named Riemannian manifold-based alternating direction method of multipliers (RM-ADMM), is developed to decompose the QCQP into simpler QCQPs with a single constraint each, and solve them efficiently in a decentralized manner. Simulations show that the proposed algorithm can significantly improve the sum-rate of the D2D-underlaid system with a reduced complexity, as compared to its alternative based on semidefinite relaxation (SDR).
Emerging applications involving device-to-device communication among wearable electronics require Gbps throughput, which can be achieved by utilizing millimeter wave (mmWave) frequency bands. When many such communicating devices are indoors in close
proximity, like in a train car or airplane cabin, interference can be a serious impairment. This paper uses stochastic geometry to analyze the performance of mmWave networks with a finite number of interferers in a finite network region. Prior work considered either lower carrier frequencies with different antenna and channel assumptions, or a network with an infinite spatial extent. In this paper, human users not only carry potentially interfering devices, but also act to block interfering signals. Using a sequence of simplifying assumptions, accurate expressions for coverage and rate are developed that capture the effects of key antenna characteristics like directivity and gain, and are a function of the finite area and number of users. The assumptions are validated through a combination of analysis and simulation. The main conclusions are that mmWave frequencies can provide Gbps throughput even with omni-directional transceiver antennas, and larger, more directive antenna arrays give better system performance.
In this paper, we consider the dynamic power control for delay-aware D2D communications. The stochastic optimization problem is formulated as an infinite horizon average cost Markov decision process. To deal with the curse of dimensionality, we utili
ze the interference filtering property of the CSMA-like MAC protocol and derive a closed-form approximate priority function and the associated error bound using perturbation analysis. Based on the closed-form approximate priority function, we propose a low-complexity power control algorithm solving the per-stage optimization problem. The proposed solution is further shown to be asymptotically optimal for a sufficiently large carrier sensing distance. Finally, the proposed power control scheme is compared with various baselines through simulations, and it is shown that significant performance gain can be achieved.
Massive multiple-input multiple-output (Massive MIMO) has been realized as a promising technology for next generation wireless mobile communications, in which Spectral efficiency (SE) and energy efficiency (EE) are two critical issues. Prior estimate
s have indicated that 57% energy of the cellular system need to be supplied by the operator, especially to feed the base station (BS). While varies scheduling studies concerned on the user equipment (UE) to reduce the total energy consumption instead of BS. Fewer literatures address EE issues from a BS perspective. In this paper, an EE scheme is proposed by reducing the energy consumption of BS. The transmission model and parameters related to EE is formulated first. Afterwards, an cellular partition zooming (CPZ) scheme is proposed where the BS can zoom in to maintain the coverage area. Specifically, if no user exists in the rare area of the coverage, BS will zoom out to sleep mode to save energy. Comprehensive simulation results demonstrate that CPZ has better EE performance with negligible impact on transmission rate.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
