اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCurrent driven asymmetric magnetization switching in perpendicularly magnetized CoFeB/MgO heterostructures
240
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The flow of in-plane current through ultrathin magnetic heterostructures can cause magnetization switching or domain wall nucleation owing to bulk and interfacial effects. Within the magnetic layer, the current can create magnetic instabilities via spin transfer torques (STT). At interface(s), spin current generated from the spin Hall effect in a neighboring layer can exert torques, referred to as the spin Hall torques, on the magnetic moments. Here, we study current induced magnetization switching in perpendicularly magnetized CoFeB/MgO heterostructures with a heavy metal (HM) underlayer. Depending on the thickness of the HM underlayer, we find distinct differences in the inplane field dependence of the threshold switching current. The STT is likely responsible for the magnetization reversal for the thinner underlayer films whereas the spin Hall torques cause the switching for thicker underlayer films. For the latter, we find differences in the switching current for positive and negative currents and initial magnetization directions. We find that the growth process during the film deposition introduces an anisotropy that breaks the symmetry of the system and causes the asymmetric switching. The presence of such symmetry breaking anisotropy enables deterministic magnetization switching at zero external fields.
قيم البحث
اقرأ أيضاً
Current-driven magnetization switching in low-resistance Co40Fe40B20/MgO/Co40Fe40B20 magnetic tunnel junctions (MTJs) is reported. The critical-current densities Jc required for current-driven switching in samples annealed at 270C and 300C are found
to be as low as 7.8 x 10^5 A/cm^2 and 8.8 x 10^5 A/cm^2 with accompanying tunnel magnetoresistance (TMR) ratios of 49% and 73 %, respectively. Further annealing of the samples at 350C increases TMR ratio to 160 %, while accompanying Jc increases to 2.5 x 10^6 A/cm^2. We attribute the low Jc to the high spin-polarization of tunnel current and small MsV product of the CoFeB single free layer, where Ms is the saturation magnetization and V the volume of the free layer.
We report the intrinsic critical current density (Jc0) in current-induced magnetization switching and the thermal stability factor (E/kBT, where E, kB, and T are the energy potential, the Boltzmann constant, and temperature, respectively) in MgO base
d magnetic tunnel junctions with a Co40Fe40B20(2nm)/Ru(0.7-2.4nm)/Co40Fe40B20(2nm) synthetic ferrimagnetic (SyF) free layer. We show that Jc0 and E/kBT can be determined by analyzing the average critical current density as a function of coercivity using the Slonczewskis model taking into account thermal fluctuation. We find that high antiferromagnetic coupling between the two CoFeB layers in a SyF free layer results in reduced Jc0 without reducing high E/kBT.
We investigated the effect of using a synthetic ferrimagnetic (SyF) free layer in MgO-based magnetic tunnel junctions (MTJs) on current-induced magnetization switching (CIMS), particularly for application to spin-transfer torque random access memory
(SPRAM). The employed SyF free layer had a Co40Fe40B20/ Ru/ Co40Fe40B20 and Co20Fe60B20/Ru/Co20Fe60B20 structures, and the MTJs(100x(150-300) nm^2) were annealed at 300oC. The use of SyF free layer resulted in low intrinsic critical current density (Jc0) without degrading the thermal-stability factor (E/kBT, where E, kB, and T are the energy potential, the Boltzmann constant, and temperature,respectively). When the two CoFeB layers of a strongly antiferromagnetically coupled SyF free layer had the same thickness, Jc0 was reduced to 2-4x10^6 A/cm^2. This low Jc0 may be due to the decreased effective volume under the large spin accumulation at the CoFeB/Ru. The E/kBT was over 60, resulting in a retention time of over ten years and suppression of the write current dispersion for SPRAM. The use of the SyF free layer also resulted in a bistable (parallel/antiparallel) magnetization configuration at zero field, enabling the realization of CIMS without the need to apply external fields to compensate for the offset field.
Spin-orbit torque can drive electrical switching of magnetic layers. Here, we report that at least for micrometer-sized samples there is no simple correlation between the efficiency of dampinglike spin-orbit torque ({xi}_DL^j) and the critical switch
ing current density of perpendicularly magnetized spin-current generator/ferromagnet heterostructures. We find that the values of {xi}_DL^j based on switching current densities can either under- or over-estimated {xi}_DL^j by up to tens of times in a domain-wall depinning analysis, while in the macrospin analysis based on the switching current density {xi}_DL^j can be overestimated by up to thousands of times. When comparing the relative strengths of {xi}_DL^j of spin-current generators, the critical switching current densities by themselves are a poor predictor.
Voltage control of magnetism and spintronics have been highly desirable, but rarely realized. In this work, we show voltage-controlled spin-orbit torque (SOT) switching in W/CoFeB/MgO films with perpendicular magnetic anisotropy (PMA) with voltage ad
ministered through SrTiO3 with a high dielectric constant. We show that a DC voltage can significantly lower PMA by 45%, reduce switching current by 23%, and increase the damping-like torque as revealed by the first and second-harmonic measurements. These are characteristics that are prerequisites for voltage-controlled and voltage-select SOT switching spintronic devices.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
