اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدHigh-Q optomechanical circuits made from polished nanocrystalline diamond thin films
224
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We demonstrate integrated optomechanical circuits with high mechanical quality factors prepared from nanocrystalline diamond thin films. Using chemomechanical polishing, the RMS surface roughness of as grown polycrystalline diamond films is reduced below 3nm to allow for the fabrication of high-quality nanophotonic circuits. By integrating free-standing nanomechanical resonators into integrated optical devices, efficient read-out of the thermomechanical motion of diamond resonators is achieved with on-chip Mach-Zehnder interferometers. Mechanical quality factors up to 28,800 are measured for four-fold clamped optomechanical resonators coupled to the evanescent near-field of nanophotonic waveguides. Our platform holds promise for large-scale integration of optomechanical circuits for on-chip metrology and sensing applications.
قيم البحث
اقرأ أيضاً
Diamond integrated photonic devices are promising candidates for emerging applications in nanophotonics and quantum optics. Here we demonstrate active modulation of diamond nanophotonic circuits by exploiting mechanical degrees of freedom in free-sta
nding diamond electro-optomechanical resonators. We obtain high quality factors up to 9600, allowing us to read out the driven nanomechanical response with integrated optical interferometers with high sensitivity. We are able to excite higher order mechanical modes up to 115 MHz and observe the nanomechanical response also under ambient conditions.
Silicon on insulator photonics has offered a versatile platform for the recent development of integrated optomechanical circuits. However, there are some constraints such as the high cost of the wafers and limitation to a single physical device level
. In the present work we investigate nanocrystalline silicon as an alternative material for optomechanical devices. In particular, we demonstrate that optomechanical crystal cavities fabricated of nanocrystalline silicon have optical and mechanical properties enabling non-linear dynamical behaviour and effects such as thermo-optic/free-carrier-dispersion self-pulsing, phonon lasing and chaos, all at low input laser power and with typical frequencies as high as 0.3 GHz.
We have studied the structural and superconducting properties of MgB$_2$ thin films made by pulsed laser deposition followed by in situ annealing. The cross-sectional transmission electron microscopy reveals a nanocrystalline mixture of textured MgO
and MgB$_2$ with very small grain sizes. A zero-resistance transition temperature ($T_{c0}$) of 34 K and a zero-field critical current density ($J_c$) of $1.3 times 10^6$ A/cm$^2$ were obtained. The irreversibility field was $sim$ 8 T at low temperatures, although severe pinning instability was observed. These bulk-like superconducting properties show that the in situ deposition process can be a viable candidate for MgB$_2$ Josephson junction technologies.
Advancement of diamond based photonic circuitry requires robust fabrication protocols of key components, including diamond resonators and cavities. Here, we present 1D (nanobeam) photonic crystal cavities generated from single crystal diamond membran
es utilising a metallic tungsten layer as a restraining, conductive and removable hard mask. The use of tungsten instead of a more conventional silicon oxide layer enables good repeatability and reliability of the fabrication procedures. The process yields high quality diamond cavities with quality factors (Q factors) approaching 10$^$4. Finally, we show that the cavities can be picked up and transferred onto a trenched substrate to realise fully suspended diamond cavities. Our fabrication process demonstrates the capability of diamond membranes as modular components for broader diamond based quantum photonic circuitry.
As wide bandgap electronic devices have continued to advance in both size reduction and power handling capabilities, heat dissipation has become a significant concern. To mitigate this, chemical vapor deposited (CVD) diamond has been demonstrated as
an effective solution for thermal management of these devices by directly growing onto the transistor substrate. A key aspect of power and radio frequency (RF) electronic devices involves transient switching behavior, which highlights the importance of understanding the temperature dependence of the heat capacity and thermal conductivity when modeling and predicting device electrothermal response. Due to the complicated microstructure near the interface between CVD diamond and electronics, it is difficult to measure both properties simultaneously. In this work, we use time domain thermoreflectance (TDTR) to simultaneously measure the in plane thermal conductivity and heat capacity of a 1 um thick CVD diamond film, and also use the pump as an effective heater to perform temperature dependent measurements. The results show that the in plane thermal conductivity varied slightly with an average of 103 W per meter per K over a temperature range of 302 to 327 K, while the specific heat capacity has a strong temperature dependence over the same range and matches with heat capacity data of natural diamond in literature.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
