اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCarbon coating of the SPS dipole chambers
122
0
0.0
(
0
)
نشر من قبل
Scientific Information Service CERN
تاريخ النشر
2013
مجال البحث
فيزياء
والبحث باللغة
English
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The Electron Multipacting (EM) phenomenon is a limiting factor for the achievement of high luminosity in accelerators for positively charged particles and for the performance of RF devices. At CERN, the Super Proton Synchrotron (SPS) must be upgraded in order to feed the Large Hadron Collider (LHC) with 25 ns bunch spaced beams. At such small bunch spacing, EM may limit the performance of the SPS and consequently that of the LHC. To mitigate this phenomenon CERN is developing a carbon thin film coating with low Secondary Electron Yield (SEY) to coat the internal walls of the SPS dipoles beam pipes. This paper presents the progresses in the coating technology, the performance of the carbon coatings and the strategy for a large scale production.
قيم البحث
اقرأ أيضاً
To rectify the problems of electron clouds observed in RHIC and unacceptable ohmic heating for superconducting magnets that can limit future machine upgrades, we started developing a robotic plasma deposition technique for $in-situ$ coating of the RH
IC 316LN stainless steel cold bore tubes based on staged magnetrons mounted on a mobile mole for deposition of Cu followed by amorphous carbon (a-C) coating. The Cu coating reduces wall resistivity, while a-C has low SEY that suppresses electron cloud formation. Recent RF resistivity computations indicate that 10 {mu}m of Cu coating thickness is needed. But, Cu coatings thicker than 2 {mu}m can have grain structures that might have lower SEY like gold black. A 15-cm Cu cathode magnetron was designed and fabricated, after which, 30 cm long samples of RHIC cold bore tubes were coated with various OFHC copper thicknesses; room temperature RF resistivity measured. Rectangular stainless steel and SS discs were Cu coated. SEY of rectangular samples were measured at room; and, SEY of a disc sample was measured at cryogenic temperatures.
The DsTau project proposes to study tau-neutrino production in high-energy proton interactions. The outcome of this experiment are prerequisite for measuring the $ u_tau$ charged-current cross section that has never been well measured. Precisely meas
uring the cross section would enable testing of lepton universality in $ u_tau$ scattering and it also has practical implications for neutrino oscillation experiments and high-energy astrophysical $ u_tau$ observations. $D_s$ mesons, the source of tau neutrinos, following high-energy proton interactions will be studied by a novel approach to detect the double-kink topology of the decays $D_s rightarrow tau u_tau$ and $taurightarrow u_tau X$. Directly measuring $D_srightarrow tau$ decays will provide an inclusive measurement of the $D_s$ production rate and decay branching ratio to $tau$. The momentum reconstruction of $D_s$ will be performed by combining topological variables. This project aims to detect 1,000 $D_s rightarrow tau$ decays in $2.3 times 10^8$ proton interactions in tungsten target to study the differential production cross section of $D_s$ mesons. To achieve this, state-of-the-art emulsion detectors with a nanometric-precision readout will be used. The data generated by this project will enable the $ u_tau$ cross section from DONUT to be re-evaluated, and this should significantly reduce the total systematic uncertainty. Furthermore, these results will provide essential data for future $ u_tau$ experiments such as the $ u_tau$ program in the SHiP project at CERN. In addition, the analysis of $2.3 times 10^8$ proton interactions, combined with the expected high yield of $10^5$ charmed decays as by-products, will enable the extraction of additional physical quantities.
The recent theoretical study on the multilayer-coating model published in Applied Physics Letters [1] is reviewed. Magnetic-field attenuation behavior in a multilayer coating model is different from a semi-infinite superconductor and a superconductin
g thin film. This difference causes that of the vortex-penetration field at which the Bean-Livingston surface barrier disappears. A material with smaller penetration depth, such as a pure Nb, is preferable as the substrate for pushing up the vortex-penetration field of the superconductor layer. The field limit of the whole structure of the multilayer coating model is limited not only by the vortex-penetration field of the superconductor layer, but also by that of the substrate. Appropriate thicknesses of superconductor and insulator layers can be extracted from contour plots of the field limit of the multilayer coating model given in Ref.[1].
Recently, the ATOMKI experiment has reported new evidence for the excess of $e^+ e^-$ events with a mass $sim$17 MeV in the nuclear transitions of $^4$He, that they previously observed in measurements with $^8$Be. These observations could be explaine
d by the existence of a new vector $X17$ boson. So far, the search for the decay $X17 rightarrow e^+ e^-$ with the NA64 experiment at the CERN SPS gave negative results. Here, we present a new technique that could be implemented in NA64 aiming to improve the sensitivity and to cover the remaining $X17$ parameter space. If a signal-like event is detected, an unambiguous observation is achieved by reconstructing the invariant mass of the $X17$ decay with the proposed method. To reach this goal an optimization of the $X17$ production target, as well as an efficient and accurate reconstruction of two close decay tracks, is required. A dedicated analysis of the available experimental data making use of the trackers information is presented. This method provides independent confirmation of the NA64 published results [Phys. Rev. D101, 071101 (2020)], validating the tracking procedure. The detailed Monte Carlo study of the proposed setup and the background estimate shows that the goal of the proposed search is feasible.
We have measured the water and hydrogen outgassing rates of seven vacuum chambers of identical geometry but constructed of different materials and heat treatments. Chambers of five different materials were tested: 304L, 316L, and 316LN stainless stee
ls; titanium (ASTM grade 2); and 6061 aluminum. In addition, chambers constructed of 316L and 316LN stainless steel were subjected to a vacuum-fire process, where they were heated to approximately 950 {deg}C for 24 hours while under vacuum; these two chambers are designated as 316L-XHV and 316LN-XHV. All chambers were of identical geometry and made by the same manufacturer, thus a relative comparison of the outgassing rates among these chambers can be made. Water outgassing rates were measured as a function of time using the throughput technique. The water outgassing results for the 316L, 316LN, 316L-XHV, 316LN-XHV were all similar, but lower than those of 304L by a factor of 3 to 5 lower at 10^4 s. The water outgassing results for Ti and Al chambers were close to that of 304L, Ti being slightly lower. Hydrogen outgassing rates were measured using the rate-of-rise method and performed after a low-temperature bake of 125 {deg}C to 150 {deg}C for a minimum of 72 hours. The Ti, Al, 316L-XHV, and 316LN-XHV chambers all have specific outgassing rates below 1 X 10^-11 Pa L s^-1 cm^-2 and are at least a factor of 100 or better than the 304L chamber. The 304L, 316L, and 316LN chambers without vacuum-fire heat treatment have larger hydrogen outgassing rates than the other chambers, with specific outgassing rates ranging between 4.0 X 10^-11 Pa L s^-1 cm^-2 and 8.0 X 10^-11 Pa L s^-1 cm^-2. We conclude that Ti, Al, 316L-XHV, and 316LN-XHV have hydrogen outgassing rates that make them excellent choices for ultra-high vacuum (UHV) and extreme-high vacuum (XHV) applications, the choice depending on cost and other material properties.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
