اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدGraphene-based charge sensors
144
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We discuss graphene nanoribbon-based charge sensors and focus on their functionality in the presence of external magnetic fields and high frequency pulses applied to a nearby gate electrode. The charge detectors work well with in-plane magnetic fields of up to 7 T and pulse frequencies of up to 20 MHz. By analyzing the step height in the charge detectors current at individual charging events in a nearby quantum dot, we determine the ideal operation conditions with respect to the applied charge detector bias. Average charge sensitivities of 1.3*10^-3 e/sqrt{Hz} can be achieved. Additionally, we investigate the back action of the charge detector current on the quantum transport through a nearby quantum dot. By setting the charge detector bias from 0 to 4.5 mV, we can increase the Coulomb peak currents measured at the quantum dot by a factor of around 400. Furthermore, we can completely lift the Coulomb blockade in the quantum dot.
قيم البحث
اقرأ أيضاً
We investigate charge transport in C$_{60}$-based single-molecule junctions with graphene electrodes employing a combination of density functional theory (DFT) electronic structure calculations and Landauer transport theory. In particular, the depend
ence of the transport properties on the conformation of the molecular bridge and the type of termination of the graphene electrodes is investigated. Furthermore, electron pathways through the junctions are analyzed using the theory of local currents. The results reveal, in agreement with previous experiments, a pronounced dependence of the transport properties on the bias polarity, which is rationalized in terms of the electronic structure of the molecule. It is also shown that the edge states of zigzag-terminated graphene induce additional transport channels, which dominate transport at small voltages. The importance of the edge states for transport depends profoundly on the interface geometry of the junctions.
Understanding spin physics in graphene is crucial for developing future two-dimensional spintronic devices. Recent studies show that efficient spin-to-charge
Graphene (G) is a two-dimensional material with exceptional sensing properties. In general, graphene gas sensors are produced in field effect transistor configuration on several substrates. The role of the substrates on the sensor characteristics has
not yet been entirely established. To provide further insight on the interaction between ammonia molecules (NH3) and graphene devices, we report experimental and theoretical studies of NH3 graphene sensors with graphene supported on three substrates: SiO2, talc and hexagonal boron nitride (hBN). Our results indicate that the charge transfer from NH3 to graphene depends not only on extrinsic parameters like temperature and gas concentration, but also on the average distance between the graphene sheet and the substrate. We find that the average distance between graphene and hBN crystals is the smallest among the three substrates, and that graphene-ammonia gas sensors based on a G/hBN heterostructure exhibit the fastest recovery times for NH3 exposure and are slightly affected by wet or dry air environment. Moreover, the dependence of graphene-ammonia sensors on different substrates indicates that graphene sensors exhibit two different adsorption processes for NH3 molecules: one at the top of the graphene surface and another at its bottom side close to the substrate. Therefore, our findings show that substrate engineering is crucial to the development of graphene-based gas sensors and indicate additional routes for faster sensors.
We report measurements on a graphene quantum dot with an integrated graphene charge detector. The quantum dot device consists of a graphene island (diameter approx. 200 nm) connected to source and drain contacts via two narrow graphene constrictions.
From Coulomb diamond measurements a charging energy of 4.3 meV is extracted. The charge detector is based on a 45 nm wide graphene nanoribbon placed approx. 60 nm from the island. We show that resonances in the nanoribbon can be used to detect individual charging events on the quantum dot. The charging induced potential change on the quantum dot causes a step-like change of the current in the charge detector. The relative change of the current ranges from 10% up to 60% for detecting individual charging events.
The magnetic field-dependent longitudinal and Hall components of the resistivity rho_xx(H) and rho_xy(H) are measured in graphene on silicon dioxide substrates at temperatures from 1.6 K to room temperature. At charge densities near the charge-neutra
lity point rho_xx(H) is strongly enhanced and rho_xy(H) is suppressed, indicating nearly equal electron and hole contributions to the transport current. The data are inconsistent with uniformly distributed electron and hole concentrations (two-fluid model) but in excellent agreement with the recent theoretical prediction for inhomogeneously distributed electron and hole regions of equal mobility. At low temperatures and high magnetic fields rho_xx(H) saturates to a value ~h/e^2, with Hall conductivity << e^2/h, which may indicate a regime of localized v = 2 and v = -2 quantum Hall puddles.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
