اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدInductive determination of the optimum tunnel barrier thickness in magnetic tunnelling junction stacks for spin torque memory applications
102
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We use pulsed inductive microwave magnetometry to study the precessional magnetization dynamics of the free layer in CoFeB/MgO/CoFeB based magnetic tunnelling junction stacks with varying MgO barrier thickness. From the field dependence of the precession frequency we are able to derive the uniaxial anisotropy energy and the exchange coupling between the free and the pinned layer. Furthermore the field dependence of the effective damping parameter is derived. Below a certain threshold barrier thickness we observe an increased effective damping for antiparallel orientation of free and pinned layer which would inhibit reversible low current density spin torque magnetization reversal. Such inductive measurements, in combination with wafer probe station based magneto transport experiments, allow a fast determination of the optimum tunnel barrier thickness range for spin torque memory applications in a lithography free process.
قيم البحث
اقرأ أيضاً
There are pressing problems with traditional computing, especially for accomplishing data-intensive and real-time tasks, that motivate the development of in-memory computing devices to both store information and perform computation. Magnetic tunnel j
unction (MTJ) memory elements can be used for computation by manipulating a domain wall (DW), a transition region between magnetic domains. But, these devices have suffered from challenges: spin transfer torque (STT) switching of a DW requires high current, and the multiple etch steps needed to create an MTJ pillar on top of a DW track has led to reduced tunnel magnetoresistance (TMR). These issues have limited experimental study of devices and circuits. Here, we study prototypes of three-terminal domain wall-magnetic tunnel junction (DW-MTJ) in-memory computing devices that can address data processing bottlenecks and resolve these challenges by using perpendicular magnetic anisotropy (PMA), spin-orbit torque (SOT) switching, and an optimized lithography process to produce average device tunnel magnetoresistance TMR = 164%, resistance-area product RA = 31 {Omega}-{mu}m^2, close to the RA of the unpatterned film, and lower switching current density compared to using spin transfer torque. A two-device circuit shows bit propagation between devices. Device initialization variation in switching voltage is shown to be curtailed to 7% by controlling the DW initial position, which we show corresponds to 96% accuracy in a DW-MTJ full adder simulation. These results make strides in using MTJs and DWs for in-memory and neuromorphic computing applications.
We investigate the spin-dependent Seebeck coefficient and the tunneling magneto thermopower of CoFeB/MgO/CoFeB magnetic tunnel junctions (MTJ) in the presence of thermal gradients across the MTJ. Thermal gradients are generated by an electric heater
on top of the nanopillars. The thermo power voltage across the MTJ is found to scale linearly with the heating power and reveals similar field dependence as the tunnel magnetoresistance. The amplitude of the thermal gradient is derived from calibration measurements in combination with finite element simulations of the heat flux. Based on this, large spin-dependent Seebeck coefficients of the order of (240 pm 110) muV/K are derived. From additional measurements on MTJs after dielectric breakdown, a tunneling magneto thermopower up to 90% can be derived for 1.5 nm MgO based MTJ nanopillars.
The thermal spin-transfer torque (TSTT) is an effect to switch the magnetic free layer in a magnetic tunnel junction by a temperature gradient only. We present ab initio calculations of the TSTT. In particular, we discuss the influence of magnetic la
yer composition by considering $text{Fe}_text{x}text{Co}_{text{1-x}}$ alloys. Further, we compare the TSTT to the bias voltage driven STT and discuss the requirements for a possible thermal switching. For example, only for very thin barriers of 3 monolayers MgO a thermal switching is imaginable. However, even for such a thin barrier the TSTT is still too small for switching at the moment and further optimization is needed. In particular, the TSTT strongly depends on the composition of the ferromagentic layer. In our current study it turns out that at the chosen thickness of the ferromagnetic layer pure Fe gives the highest thermal spin-transfer torque.
We simulate the spin torque-induced reversal of the magnetization in thin disks with perpendicular anisotropy at zero temperature. Disks typically smaller than 20 nm in diameter exhibit coherent reversal. A domain wall is involved in larger disks. We
derive the critical diameter of this transition. Using a proper definition of the critical voltage, a macrospin model can account perfectly for the reversal dynamics when the reversal is coherent. The same critical voltage appears to match with the micromagnetics switching voltage regardless of the switching path.
Understanding the magnetization dynamics induced by spin transfer torques in perpendicularly magnetized magnetic tunnel junction nanopillars and its dependence on material parameters is critical to optimizing device performance. Here we present a mic
romagnetic study of spin-torque switching in a disk-shaped element as a function of the free layers exchange constant and disk diameter. The switching is shown to generally occur by 1) growth of the magnetization precession amplitude in the element center; 2) an instability in which the reversing region moves to the disk edge, forming a magnetic domain wall; and 3) the motion of the domain wall across the element. For large diameters and small exchange, step 1 leads to a droplet with a fully reversed core that experiences a drift instability (step 2). While in the opposite case (small diameters and large exchange), the central region of the disk is not fully reversed before step 2 occurs. The origin of the micromagnetic structure is shown to be the disks non-uniform demagnetization field. Faster, more coherence and energy efficient switching occur with larger exchange and smaller disk diameters, showing routes to increase device performance.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
