اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدVelocity, temperature and normal force dependence on friction: An analytical and molecular dynamic study
221
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this work we propose an extension to the analytical one-dimensional model proposed by E. Gnecco (Phys. Rev. Lett. 84:1172) to describe friction. Our model includes normal forces and the dependence with the angular direction of movement in which the object is dragged over a surface. The presence of the normal force in the model allow us to define judiciously the friction coefficient, instead of introducing it as an {sl a posteriori} concept. We compare the analytical results with molecular dynamics simulations. The simulated model corresponds to a tip sliding over a surface. The tip is simulated as a single particle interacting with a surface through a Lennard-Jones $(6-12)$ potential. The surface is considered as consisting of a regular BCC(001) arrangement of particles interacting with each other through a Lennard-Jones $(6-12)$ potential. We investigate the system under several conditions of velocity, temperature and normal forces. Our analytical results are in very good agreement with those obtained by the simulations and with experimental results from E. Riedo (Phys. Rev. Lett. 91:084502) and Eui-Sung Yoon (Wear 259:1424-1431) as well.
قيم البحث
اقرأ أيضاً
In this work we present a molecular dynamics simulation of a FFM experiment. The tip-sample interaction is studied by varying the normal force in the tip and the temperature of the surface. The friction force, cA, at zero load and the friction coeffi
cient, $mu$, were obtained. Our results strongly support the idea that the effective contact area, A, decreases with increasing temperature and the friction coefficient presents a clear signature of the premelting process of the surface.
We present concise, computationally efficient formulas for several quantities of interest -- including absorbed and scattered power, optical force (radiation pressure), and torque -- in scattering calculations performed using the boundary-element met
hod (BEM) [also known as the method of moments (MOM)]. Our formulas compute the quantities of interest textit{directly} from the BEM surface currents with no need ever to compute the scattered electromagnetic fields. We derive our new formulas and demonstrate their effectiveness by computing power, force, and torque in a number of example geometries. Free, open-source software implementations of our formulas are available for download online.
The dissipation of energy in dynamic force microscopy is usually described in terms of an adhesion hysteresis mechanism. This mechanism should become less efficient with increasing temperature. To verify this prediction we have measured topography an
d dissipation data with dynamic force microscopy in the temperature range from 100 K up to 300 K. We used 3,4,9,10-perylenetetracarboxylic-dianhydride (PTCDA) grown on KBr(001), both materials exhibiting a strong dissipation signal at large frequency shifts. At room temperature, the energy dissipated into the sample (or tip) is 1.9 eV/cycle for PTCDA and 2.7 eV/cycle for KBr, respectively, and is in good agreement with an adhesion hysteresis mechanism. The energy dissipation over the PTCDA surface decreases with increasing temperature yielding a negative temperature coefficient. For the KBr substrate, we find the opposite behaviour: an increase of dissipated energy with increasing temperature. While the negative temperature coefficient in case of PTCDA agrees rather well with the adhesion hysteresis model, the positive slope found for KBr points to a hitherto unknown dissipation mechanism.
This paper is concerned with tuning friction and temperature in Langevin dynamics for fast sampling from the canonical ensemble. We show that near-optimal acceleration is achieved by choosing friction so that the local quadratic approximation of the
Hamiltonian is a critical damped oscillator. The system is also over-heated and cooled down to its final temperature. The performances of different cooling schedules are analyzed as functions of total simulation time.
The displacement field for three dimensional dynamic elasticity problems in the frequency domain can be decomposed into a sum of a longitudinal and a transversal part known as a Helmholtz decomposition. The Cartesian components of both the longitudin
al and transverse fields satisfy scalar Helmholtz equations that can be solved using a desingularized boundary element method (BEM) framework. The curl free longitudinal and divergence free transversal conditions can also be cast as additional scalar Helmholtz equations. When compared to other BEM implementations, the current framework leads to smaller matrix dimensions and a simpler conceptual approach. The numerical implementation of this approach is benchmarked against the 3D elastic wave field generated by a rigid vibrating sphere embedded in an infinite linear elastic medium for which the analytical solution has been derived. Examples of focussed 3D elastic waves generated by a vibrating bowl-shaped rigid object with convex and concave surfaces are also considered. In the static zero frequency limit, the Helmholtz decomposition becomes non-unique, and both the longitudinal and transverse components contain divergent terms that are proportional to the inverse square of the frequency. However, these divergences are equal and opposite so that their sum, that is the displacement field that reflects the physics of the problem, remains finite in the zero frequency limit.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
