اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCharacterization of Flexible RF Microcoil Dedicated to Surface Mri
534
0
0.0
(
0
)
نشر من قبل
EDA Publishing Association
تاريخ النشر
2007
مجال البحث
الهندسة المعلوماتية
والبحث باللغة
English
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In Magnetic Resonance Imaging (MRI), to achieve sufficient Signal to Noise Ratio (SNR), the electrical performance of the RF coil is critical. We developed a device (microcoil) based on the original concept of monolithic resonator. This paper presents the used fabrication process based on micromoulding. The dielectric substrates are flexible thin films of polymer, which allow the microcoil to be form fitted to none-plane surface. Electrical characterizations of the RF coils are first performed and results are compared to the attempted values. Proton MRI of a saline phantom using a flexible RF coil of 15 mm in diameter is performed. When the coil is conformed to the phantom surface, a SNR gain up to 2 is achieved as compared to identical but planar RF coil. Finally, the flexible coil is used in vivo to perform MRI with high spatial resolution on a mouse using a small animal dedicated scanner operating at in a 2.35 T.
قيم البحث
اقرأ أيضاً
We present and discuss the fabrication process and the performance of a flexible micro thermoelectric generator with electroplated Bi2Te3 thermocouples in a SU-8 mold. Demonstrator devices generate 278uWcm-2 at dTmeas=40K across the experimental set
up. Based on model calculations, a temperature difference of dTG=21.4K across the generator is assumed. Due to the flexible design and the chosen generator materials, the performance stays high even for curved contact surfaces. The measurement results correlate well with the model based design optimization predictions.
Pb(Zr0.52Ti0.48)O3 (PZT) thin films were in situ deposited by pulsed laser deposition (PLD) on Pt/Ti/SiO2/Si substrates using a template layer derived by sol-gel method. A 0.1-$mu$m-thick PZT layer with (111) or (100)-preferred orientation was first
deposited onto Pt/Ti/SiO2/Si substrates using the sol-gel method, and than a PZT layer with thickness of 1$mu$m was in situ deposited by PLD on the above-mentioned PZT layer. The crystalline phases and the preferred orientations of the PZT films were investigated by X-ray diffraction analysis. Surface and cross-sectional morphologies were observed by scanning electron microscopy and transmission electron microscopy. The electrical properties of the films were evaluated by measuring their P-E hysteresis loops and dielectric constants. The preferred orientation of the films can be controlled using the template layer derived by the sol-gel method. The deposition temperature required to obtain the perovskite phase in this process is approximately 460 degrees C, and is significantly lower than that in the case of direct film deposition by PLD on the Pt/Ti/SiO2/Si substrates. Keywords: lead zirconate titanate (PZT), thin film, sol-gel method, laser ablation, electrical properties
Purpose: To develop a robust and flexible low power water excitation pulse that enables effective fat suppression at high magnetic field strength. Methods: A water excitation method that uses spatially non-selective pulses was optimized in numerical
simulations, and implemented and tested in phantoms and healthy volunteers at 3T. The lipid insensitive binomial off-resonant excitation (LIBRE) pulse comprises two low power rectangular sub-pulses that have a variable frequency offset, phase offset and duration. The capability and extent of LIBRE fat suppression was quantitatively compared with conventional fat saturation (FS) and water excitation (WE) techniques. Results: LIBRE enables simultaneous water excitation and near complete fat suppression in large volumes at 3T as demonstrated by numerical simulations, and experiments. In phantoms and in human subjects, the frequency responses matched well with those from the numerical simulation. Comparing FS and WE, LIBRE demonstrated an improved robustness to magnetic field inhomogeneities, and a much more effectively suppressed fat signal. This applied for a range of pulse durations and pulses as short as 1.4 ms. Conclusion: A flexible water excitation method was developed that shows robust, near complete fat suppression at 3T.
For decades, wireless energy transfer and harvesting remained of focused attention in the research community, but with limited practical applications. Recently, with the development of fifth-generation (5G) mobile technology, the concept of dedicated
radio-frequency (RF) charging promises to support the growing market of wearable devices. In this work, we shed light on the potential of wireless RF power transfer by elaborating upon feasible system parameters and architecture, emphasizing the basic trade-offs behind omni-directional and directional out-of-band energy transmission, providing system-level performance evaluation, as well as discussing open challenges on the way to sustainable wireless-powered wearables. The key aspects highlighted in this article include system operation choices, user mobility effects, impact of network and user densities, as well as regulatory issues. Ultimately, our research targets to facilitate the integration of wireless RF charging technology into the emerging 5G ecosystem.
This paper presents a new electrostatic MEMS (MicroElectroMechanical System) based on a single high reliability totally free flexible membrane. Using four electrodes, this structure enables four states which allowed large deflections (4$mu$m) with lo
w actuation voltage (7,5V). This design presents also a good contact force and improve the restoring force of the structure. As an example of application, a Single Pole Double Throw (SPDT) for 24GHz applications, based on this design, has been simulated.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
