اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدA surprising method for polarising antiprotons
99
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We propose a method for polarising antiprotons in a storage ring by means of a polarised positron beam moving parallel to the antiprotons. If the relative velocity is adjusted to $v/c approx 0.002$ the cross section for spin-flip is as large as about $2 cdot 10^{13}$ barn as shown by new QED-calculations of the triple spin-cross sections. Two possibilities for providing a positron source with sufficient flux density are presented. A polarised positron beam with a polarisation of 0.70 and a flux density of approximately $1.5 cdot 10^{10}$/(mm$^2$ s) appears to be feasible by means of a radioactive $^{11}$C dc-source. A more involved proposal is the production of polarised positrons by pair production with circularly polarised photons. It yields a polarisation of 0.76 and requires the injection into a small storage ring. Such polariser sources can be used at low (100 MeV) as well as at high (1 GeV) energy storage rings providing a time of about one hour for polarisation build-up of about $10^{10}$ antiprotons to a polarisation of about 0.18. A comparison with other proposals show a gain in the figure-of-merit by a factor of about ten.
قيم البحث
اقرأ أيضاً
The paper describes the commissioning of the experimental equipment and the machine studies required for the first spin-filtering experiment with protons at a beam kinetic energy of $49.3,$MeV in COSY. The implementation of a low-$beta$ insertion mad
e it possible to achieve beam lifetimes of $tau_{rm{b}}=8000,$s in the presence of a dense polarized hydrogen storage-cell target of areal density $d_{rm t}=(5.5pm 0.2)times 10^{13},mathrm{atoms/cm^{2}}$. The developed techniques can be directly applied to antiproton machines and allow for the determination of the spin-dependent $bar{p}p$ cross sections via spin filtering.
Cavity combiners have been put forward for high power combining due to their advantages of larger combining ability, variable input channels and less power loss. For a high power cavity combiner, it is better to keep the power loss ratio in a reasona
ble range, because large power loss would lead to strict requirements on the cooling system. A combiner with variable input channels is convenient for outputting different power levels according to practical demands. In this paper, a method for designing a variable-channel high-power cavity combiner is proposed, based on the relation between input and output coupling coefficients obtained by analyzing the equivalent circuit of the cavity combiner. This method can put the designed cavity combiner in a matching state and keep its power loss rate in a reasonable range as the number of input channels changes. As an example, a cavity combiner with 500 MHz and variable input channels from 16 to 64 is designed, and the simulation results show that our proposed method is feasible.
Iron-free CCT magnet design offers many advantages, one being the excellent field quality and the absence of multipole components. However, edge effects are present, although they tend to integrate out over the length of the magnet. Many modern accel
erator applications, however, require that these magnets are placed in an area of rapidly varying optics parameters, so magnets with greatly reduced edge effects have an advantage. We have designed such a magnet (a quadrupole) by adding multipole components of the opposite sign to the edge distortions of the magnet. A possible application could be the final focus magnets of the FCC-ee, where beam sizes at the entry and exit point of the magnets vary by large factors. We have then used this technique to effectively eliminate cross talk between adjacent final focus quadrupoles for the incoming and outgoing beams.
Using formulas for certain quantities involving stable vectors, due to I. Molchanov, and in some cases utilizing the so-called divide and color model, we prove that certain families of integrals which, ostensibly, depend on a parameter are in fact independent of this parameter.
We report on new high-resolution imaging and spectroscopy on the multiple T Tauri star system V773 Tau over the 2003 -- 2009 period. With these data we derive relative astrometry, photometry between the A and B components, and radial velocity (RV) of
the A-subsystem components. Combining these new data with previously published astrometry and RVs, we update the relative A-B orbit model. This updated orbit model, the known system distance, and A subsystem parameters yields a dynamical mass for the B component for the first time. Remarkably the derived B dynamical mass is in the range of 1.7 -- 3.0 M$_sun$. This is much higher than previous estimates, and suggests that like A, B is also a multiple stellar system. Among these data, spatially-resolved spectroscopy provide new insight into the nature of the B component. Similar to A, these near-IR spectra indicate that the dominant source in B is of mid-K spectral type. If B is in fact a multiple star system as suggested by the dynamical mass estimate, the simplest assumption is that B is composed of similar $sim$ 1.2 M$_sun$ PMS stars in a close ($<$ 1 AU) binary system. This inference is supported by line-shape changes in near-IR spectroscopy of B, tentatively interpreted as changing RV among components in V773 Tau B. Relative photometry indicate that B is highly variable in the near-IR. The most likely explanation for this variability is circum-B material resulting in variable line-of-sight extinction. The distribution of this material must be significantly affected by both the putative B multiplicity, and the A-B orbit.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
