اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدRoughness induced boundary slip in microchannel flows
171
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Surface roughness becomes relevant if typical length scales of the system are comparable to the scale of the variations as it is the case in microfluidic setups. Here, an apparent boundary slip is often detected which can have its origin in the assumption of perfectly smooth boundaries. We investigate the problem by means of lattice Boltzmann (LB) simulations and introduce an ``effective no-slip plane at an intermediate position between peaks and valleys of the surface. Our simulations show good agreement with analytical results for sinusoidal boundaries, but can be extended to arbitrary geometries and experimentally obtained surface data. We find that the detected apparent slip is independent of the detailed boundary shape, but only given by the distribution of surface heights. Further, we show that the slip diverges as the amplitude of the roughness increases.
قيم البحث
اقرأ أيضاً
Hydrodynamic slip of a liquid at a solid surface represents a fundamental phenomenon in fluid dynamics that governs liquid transport at small scales. For polymeric liquids, de Gennes predicted that the Navier boundary condition together with the theo
ry of polymer dynamics imply extraordinarily large interfacial slip for entangled polymer melts on ideal surfaces; this Navier-de Gennes model was confirmed using dewetting experiments on ultra-smooth, low-energy substrates. Here, we use capillary leveling - surface tension driven flow of films with initially non-uniform thickness - of polymeric films on these same substrates. Measurement of the slip length from a robust one-parameter fit to a lubrication model is achieved. We show that at the lower shear rates involved in leveling experiments as compared to dewetting ones, the employed substrates can no longer be considered ideal. The data is instead consistent with physical adsorption of polymer chains at the solid/liquid interface. We extend the Navier-de Gennes description using one additional parameter, namely the density of physically adsorbed chains per unit surface. The resulting formulation is found to be in excellent agreement with the experimental observations.
Classical hydrodynamic models predict that infinite work is required to move a three-phase contact line, defined here as the line where a liquid/vapor interface intersects a solid surface. Assuming a slip boundary condition, in which the liquid slide
s against the solid, such an unphysical prediction is avoided. In this article, we present the results of experiments in which a contact line moves and where slip is a dominating and controllable factor. Spherical cap shaped polystyrene microdroplets, with non-equilibrium contact angle, are placed on solid self-assembled monolayer coatings from which they dewet. The relaxation is monitored using textit{in situ} atomic force microscopy. We find that slip has a strong influence on the droplet evolutions, both on the transient non-spherical shapes and contact line dynamics. The observations are in agreement with scaling analysis and boundary element numerical integration of the governing Stokes equations, including a Navier slip boundary condition.
The shape of a microchannel during flow through it is instrumental to understanding the physics that govern various phenomena ranging from rheological measurements of fluids to separation of particles and cells. Two commonly used approaches for obtai
ning a desired channel shape (for a given application) are (i) fabricating the microchannel in the requisite shape and (ii) actuating the microchannel walls during flow to obtain the requisite shape. However, these approaches are not always viable. We propose an alternative, passive approach to {it a priori} tune the elastohydrodynamics in a microsystem, towards achieving a pre-determined (but not pre-fabricated) flow geometry when the microchannel is subjected to flow. That is to say, we use the interaction between a soft solid layer, the viscous flow beneath it and the shaped rigid wall above it, to tune the fluid domains shape. Specifically, we study a parallel-wall microchannel whose top wall is a slender soft coating of arbitrary thickness attached to a rigid platform. We derive a nonlinear differential equation for the soft coatings fluid--solid interface, which we use to infer how to achieve specific conduit shapes during flow. Using this theory, we demonstrate the tuning of four categories of microchannel geometries, which establishes, via a proof-of-concept, the viability of our modeling framework. We also explore slip length patterning on the rigid bottom wall of the microchannel, a common technique in microfluidics, as an addition `handle for microchannel shape control. However, we show that this effect is much weaker in practice.
We report rheological measurements of a noncolloidal particle suspension in a Newtonian solvent at 40% solid volume fraction. An anomalous, frequency-dependent complex viscosity is found under oscillatory shear (OS) flow, whereas a constant dynamic v
iscosity is found under the same shear rates in steady shear (SS) flow. We show that this contradiction arises from the underlying microstructural difference between OS and SS, mediated by weak interparticle forces. Discrete element simulations of proxy particle suspensions confirm this hypothesis and reveal an adhesion-induced, shear thinning mechanism with a -1/5 slope, only in OS, in agreement with experiments.
Crumpled paper or drapery patterns are everyday examples of how elastic sheets can respond to external forcing. In this Letter, we study experimentally a novel sort of forcing. We consider a circular flexible plate clamped at its center and subject t
o a uniform flow normal to its initial surface. As the flow velocity is gradually increased, the plate exhibits a rich variety of bending deformations: from a cylindrical taco-like shape, to isometric developable cones with azimuthal periodicity two or three, to eventually a rolled-up period-three cone. We show that this sequence of flow-induced deformations can be qualitatively predicted by a linear analysis based on the balance between elastic energy and pressure force work.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
